Publications
Sort:
Open Access Issue
Optimized design of stiffened panels considering the twist angle error of stringers
Journal of National University of Defense Technology 2025, 47(6): 157-167
Published: 01 December 2025
Abstract PDF (6.1 MB) Collect
Downloads:2
Objective

The structural design in the aerospace field, while pursuing high load-carrying capacity and lightweight, often leads to a significant increase in the sensitivity to structural defects and processing errors. In practical engineering, the twist angle error of stringers is one of the main processing errors of thin-walled stiffened structures. Due to the relatively few related studies, it is urgent to carry out the optimization design of stiffened panels considering the twist angle error of stringers.

Methods

The finite element model of post-buckling instability of stiffened panels under axial compression was established. The crushing failure mechanism and buckling instability mode of stiffened panels were explored, and the sensitivity of the load-carrying capacity to the twist angle error on stringers and the distribution position of the torsional stringer was analyzed. On this basis, a parallel sequential approximate optimization method based on the surrogate model was proposed by using the parallel sequential sampling strategy. This method realized parallel sequential sampling considering both exploration and development strategies, and achieved high-efficiency optimization in the complex design domain. Furthermore, based on this method, the lightweight design of a stiffened panel was carried out under the influence of twist angle error of stringers.

Results

The local instability waves of the skin between the frames and stringers caused the coupling deformation of the stringers and the skin, and the induced bending and torsion coupling warping instability of the stringers was the main reason for the overall crushing failure of the stiffened panel. For the stiffened panels studied, the torsion stringer is distributed in the middle, and the twist angle is maintained within 10°, which can effectively control the reduction factor of the bearing capacity of the stiffened panel below 1%. At the same time, reducing the width-to-thickness ratio of the flange and the height-to-thickness ratio of the web of the torsional stringer will effectively lower the sensitivity of the structural load-carrying capacity to the twist angle error of the stringer. In terms of optimization, compared with the optimization design scheme without error influence, the optimization scheme considering the twist angle error of stringers has lower sensitivity to the twist angle error when the weight is reduced by more than 32%.

Conclusions

The established post-buckling instability finite element model can effectively reveal the crushing failure mechanism of the stiffened panel under the initial twist angle error of stringers. Then, the structural forms with lower error sensitivity are given, which provide theoretical support and technical reference for the structural examination and evaluation of the existing twist angle error of stringers. In addition, the proposed parallel sequential approximate optimization method is effective for structural optimization design, considering and not considering the twist angle error of stringers, and can efficiently search for the optimal solution in the high-dimensional complex design domain. Finally, the optimized structure of stiffened panels considering the twist angle error of stringers has a higher load-carrying capacity and robustness, which has important engineering application value.

Open Access Issue
Analysis of the influence mechanism of preload variation on axial connection stiffness of clamp band joint
Journal of National University of Defense Technology 2025, 47(1): 113-125
Published: 28 February 2025
Abstract PDF (6.8 MB) Collect
Downloads:18

To accurately calculate the nonlinear bearing capacity of the CBJ (clamp band joint), through the mechanics behavior analysis of each component in the CBJ, a method for calculating the axial connection stiffness of the CBJ considering the change of preload was proposed. A fine finite element model was established considering the nonlinearity of the structure, and the accuracy of the finite element model was verified by axial tensile stiffness experiment. Combined with the finite element model, the theoretical calculation of the device connection stiffness was modified. Based on the established finite element and computational theoretical model, the influence mechanism of the distribution and variation of the belt tension and the initial belt preload on the device strength and connection stiffness was revealed. The results show that the stiffness calculation model can accurately calculate the axial connection stiffness of the device and predict the failure load of the connection, which has important engineering application value.

Open Access Issue
Low-frequency fatigue characteristics of NEPE solid propellant
Journal of National University of Defense Technology 2025, 47(1): 31-41
Published: 28 February 2025
Abstract PDF (5.8 MB) Collect
Downloads:9

To investigate the damage evolution process of low-frequency fatigue-loaded NEPE (nitrate ester plasticized polyether) solid propellant and get the influence law of fatigue loading history on tensile mechanical properties of NEPE solid propellant, the NEPE solid propellant low-frequency fatigue tests and uniaxial tensile tests with constant strain rate were conducted by the electronic universal testing machine. Based on the microscopic morphology and testing curves of test piece after fatigue loading, the influential mechanism of microscopic and mesoscopic damage on the NEPE solid propellant macroscopic mechanical behavior was further analyzed. Results indicate that the NEPE solid propellant matrix microcracks and voids at the matrix/particle interface are induced by low-frequency fatigue loads, leading to nonnegligible stress-softening behavior and residual strain. During and after fatigue loading, the attenuations of macroscopic mechanical properties of NEPE solid propellant are all exponentially related to the maximum loading strain. Part of microscopic damage by low-frequency fatigue load can recover, while the remaining fatigue damage may enhance the molecular chain orientation ability, and thus lead to the fatigue-strengthening phenomenon in materials.

Issue
Generation and release mechanism of residual stress and strain in solid rocket motor propellant grain with pressure cure
Acta Aeronautica et Astronautica Sinica 2025, 46(16)
Published: 06 February 2025
Abstract PDF (4.6 MB) Collect
Downloads:20

To investigate the generation and release mechanism of residual stress and strain in solid rocket motor propellant grain with pressure cure, a theoretical model considering the coupling of thermochemical-mechanical multi physics fields during curing and cooling process was developed based on viscoelastic theory, finite difference method, and incremental method. The composition, distribution and evolution laws of residual stress and strain of grain were revealed. The mapping relationships between temperature, degree of cure, residual stress and strain of grain were obtained. The release path of residual stress and strain of grain was optimized. The results showed that the residual stress and strain of grain were mainly caused by the accumulation of three parts: thermal expansion and cure shrinkage during curing stage, and cooling shrinkage during cooling stage. The residual stress caused by three parts accounted for about 5%, 12% and 83% respectively. The residual strain caused by three parts accounted for about −1%, 24% and 77% respectively. During cooling stage, as the temperature of grain decreases, the residual stress and strain linearly increase. Using the proposed theoretical model, the optimal pressure load of pressure cure technology was calculated, which is linearly related to the circumferential elastic modulus of the case. Compared with the conventional pressure cure technology, the optimized technology based on the composition and evolution laws of response can reduce the maximum residual stress and strain during curing and cooling process by an average of about 65.5%.

Issue
Review on analysis and control technology of curing residual stress in solid motor propellants
Acta Aeronautica et Astronautica Sinica 2025, 46(8)
Published: 16 October 2024
Abstract PDF (1.5 MB) Collect
Downloads:23

A certain residual stress will accumulate during the curing and cooling process of Solid Rocket Motor (SRM) grain, which will affect the structural integrity of the SRM. Therefore, it is of great significance to analyze the Cure-induced Residual Stress (CRS) of the propellant grain and explore effective control methods for ensuring the reliability of space vehicles and the safety of weapons and equipment. In this paper, the research progress on the generation mechanism, release method, detection technique and inversion prediction of the CRS of propellant grain is reviewed. This paper summarizes the current status and shortcomings of the structural integrity research of SRM, considering the CRS of propellant grain, as well as the development of its control methods and engineering applications. Based on the formation causes and release mechanism of the CRS and the release mechanisms in propellant grain structures, corresponding control methods and ideas for engineering application development are proposed. The analysis shows that the co-design method combining curing process control and structural configuration optimization can effectively control the CRS of the propellant grain, and establishing a standard test system is the key to validate the control method.

Total 5