Publications
Sort:
Issue
Dynamic Characteristics of RC Rigid Frame Arch Bridge Strengthened by Plate-Truss Combination
Journal of South China University of Technology (Natural Science Edition) 2023, 51(4): 31-43
Published: 25 April 2023
Abstract PDF (34 MB) Collect
Downloads:3

The common strengthening methods of reinforced concrete (RC) rigid frame arch bridges mostly belong to local strengthening rather than overall reconstruction. Therefore, the improvement of structural mechanical properties is extremely limited, making it difficult to meet the increasing demands of highway traffic loads in China's current stage. In view of the above problems, this paper firstly proposed a new strengthening method, the Method of Plate-truss Combination Strengthening. This strengthening method involves erecting steel trusses on both sides of the main beam, and uses measures such as planting rebars, welding, laying steel mesh, and pouring concrete to firmly connect the steel trusses with the main beam, forming a composite structure of a plate and truss. This transforms the structural load-bearing system from the main beam to the plate-truss composite system, achieving optimization of the structural load-bearing. Then, the above method was used to reinforce a rigid frame arch bridge. Through finite element simulation and bridge dynamic load test, the effectiveness and practicability of the new strengthening method were verified. The results show that after strengthening, the natural frequency of the structure is effectively improved, and the vertical stiffness, the bearing capacity is significantly increased. The theoretical value of vertical bending frequency in the first-order of the structure is increased by 80.5% compared to before reinforcement, and the deflection value of the structure under Highway Class-Ⅰ load is reduced by 56.8% after reinforcement compared to before. The stress level of the concrete components is reduced by 10.9% to 69.8% compared to before reinforcement. The strengthening method can improve the dynamic characteristics of the structure. The vertical vibration effect of the structure after reinforcement is less than that before reinforcement. The measured impact coefficient is much smaller than the current normative value, and the dynamic performance of the structure is good.

Issue
Multi-Factor Model of Plastic Development Coefficient and Strength Calculation for Rectangular Concrete-Filled Steel Tube Members Under Pure Bending
Journal of South China University of Technology (Natural Science Edition) 2024, 52(11): 21-31
Published: 25 November 2024
Abstract PDF (2.5 MB) Collect
Downloads:5

The constraint effect of rectangular steel pipe on core concrete has special characteristics, and the accurate prediction of the plastic development capacity of bending members can effectively ensure the load-bearing safety. In order to improve the calculation accuracy of the sectional strength of rectangular CFST members under pure bending, this study established a multi-factor model of plastic development coefficient and an improved bending strength model based on the confinement coefficient and further considering the influence of height-width ratio and steel ratio. First of all, based on the unified theory of CFST members, the change law of plastic development coefficient of rectangular concrete-filled steel tube was studied and compared with the current standard calculation formula. Then, combined with the specification and engineering needs, 2160 numerical simulation components of rectangular CFST members under pure bending were constructed and the refined analysis of the fiber model method was conducted using the improved constitutive relationship and component failure criterion. The influence of width-thickness ratio, height-width ratio, steel ratio and strength ratio on plasticity development coefficient was investigated to determine that the height-width ratio and steel ratio are the main factors influencing the plasticity development coefficient, and the function expressions related to the height-width ratio and steel ratio were fitted through regression analysis. Thus the multi-factor model of plasticity development coefficient and strength calculation of rectangular CFST members under pure bending were established. Finally, the bending strength improvement model was verified against the main design specifications at home and abroad by using the 128 sets of experimental data collected. The results show that the established multi-factor model of plasticity development coefficient overcomes the defects of the current specification that the calculation model is not accurate enough, and it can more accurately reflect the plasticity development capacity of rectangular CFST members under pure bending. The established improvement model of the bending strength of rectangular CFST members under pure bending solved for the ratio of the ultimate load carrying capacity to the experimental value has a mean value of 0.971 and a root-mean-square error of 0.118, indicating a good match and a higher calculation accuracy.

Total 2