Sort:
Open Access Original Paper Issue
An intelligent micro-nano capsule green hydrogel decorated with carbon quantum dots with delayed crosslinking characteristics for enhanced oil recovery in harsh reservoir
Petroleum Science 2025, 22(11): 4809-4822
Published: 23 September 2025
Abstract PDF (17.2 MB) Collect
Downloads:3

Hydrogels are widely used in reservoir flow control to enhanced oil recovery. However, challenges such as environmental contamination from conventional crosslinkers, poor solubility of crosslinking agents, and short gelation times under high-temperature conditions (e.g., 150 ℃) have hindered their practical application. Herein, we present the synthesis of amine-functionalized carbon quantum dots (NH2-CQDs), which act as both a nano-crosslinker and a nano-reinforcing agent within hydrogel systems. The NH2-CQDs-incorporated hydrogel can remain stability for 300 days under the conditions of a mineralization degree of 2.11 × 104 mg/mL and 170 ℃, and has high tensile strength (371 kPa), good toughness (49.6 kJ/m3), excellent viscoelasticity (G' = 960 Pa, G″ = 460 Pa) and shear resistance. In addition, NH2-CQDs adds many hydroxyl groups to the hydrogel, which can be attached to the surface of various substances. At the same time, micro-nano capsules containing NH2-CQDs were formed by self-assembly of hydrophobic SiO2 on water droplets, the NH2-CQDs solution is encapsulated in a capsule, and when stimulated by external conditions (temperature, pH, surfactant), the capsule releases the NH2-CQDs solution, this method greatly delays the crosslinking time between polymer and crosslinker at high temperature. Under the condition of 170 ℃ and pH = 7, the gelation time of 10% hydrophobic SiO2 coated hydrogel is 44 times that of uncoated hydrogel, which can be effectively used for deep formation flow control, and CQD give hydrogels fluorescence properties that can be used for underground signal tracking.

Open Access Original Paper Issue
Research on the in-situ catalytic pyrolysis of heavy oil by 2D layered MOF and its catalytic mechanism
Petroleum Science 2025, 22(8): 3434-3446
Published: 29 April 2025
Abstract PDF (3.8 MB) Collect
Downloads:15

China possesses abundant heavy oil resources, yet faces challenges such as high viscosity, underdeveloped production technologies, and elevated development cost. Although the in-situ catalytic viscosity-reduction technology can address certain technical, environmental, and cost problems during the extraction process, the catalysts often suffer from poor stability and low catalytic efficiency. In this study, a green and simple room-temperature stirring method was employed to synthesize a class of highly efficient and stable 2D MOF catalysts, which possess the capability to conduct in-situ catalytic pyrolysis of heavy oil and reduce the viscosity. Under the condition of 160 ℃, a catalyst concentration of 0.5 wt%, and a hydrogen donor (tetralin) concentration of 2 wt%, the viscosity-reduction rate of Fe-MOF is as high as 89.09%, and it can decrease the asphaltene content by 8.42%. In addition, through the structural identification and analysis of crude oil asphaltenes, the causes for the high viscosity of heavy oil are explained at the molecular level. Through the analysis of catalytic products and molecular dynamics simulation, the catalytic mechanism is studied. It is discovered that Fe-MOF can interact with heavy oil macromolecules via coordination and pore-channel effects, facilitating their cracking and dispersal. Furthermore, synergistic interactions between Fe-MOF and the hydrogen donor facilitates hydrogenation reactions and enhances the viscosity-reducing effect. This study provides a novel strategy for boosting heavy oil recovery and underscores the potential of 2D MOFs in catalytic pyrolysis applications.

Open Access Original Paper Issue
Molecular dynamics insights into wax formation—How polymeric inhibitors shape crude oil flow
Petroleum Science 2025, 22(5): 2233-2245
Published: 04 March 2025
Abstract PDF (1.9 MB) Collect
Downloads:26

Molecular-level interactions between polymeric inhibitors and wax crystals are essential for mitigating wax deposition in crude oils, a major operational and environmental challenge. This study investigates the mechanisms by which specific inhibitors target wax crystals to prevent aggregation. Extracted wax and inhibitor were characterized using gas chromatography, X-ray diffraction, and spectroscopy to determine the molecular structures. The wax primarily comprised of straight-chain nC28 alkanes, while the inhibitor was an ethylene/vinyl acetate copolymer. Rheological tests demonstrated a reduced gelation point upon inhibitor addition.

Molecular dynamics (MD) simulations, performed using the COMPASS Ⅱ force field, revealed interactions at the molecular level. Structural validation of molecules was done through comparative analysis of the experimental infrared and simulated vibrational analysis spectra whereas that of the rhombohedral wax crystal was achieved using the Pawley method, yielding a Profile R-factor of 9.26%. Morphological studies revealed five symmetrically unique facets, with the (110) plane being the fastest-growing due to its inter-planar distance and attachment energy (−157.25 kcal/mol). Adsorption energy calculations (−180 kcal/mol) confirmed that the inhibitor effectively disrupted crystal growth on the surface by adsorbing its polar section onto the wax surface while repelling the non-polar groups, thereby reducing wax aggregation.

Open Access Original Paper Issue
Research on the pollution and damage mechanism of drilling fluid on casing during ultra-deep well drilling process
Petroleum Science 2025, 22(3): 1234-1251
Published: 21 December 2024
Abstract PDF (13.7 MB) Collect
Downloads:4

In drilling ultra-deep wells, the drilling fluid circulation usually causes erosion damage to downhole casing and drilling tools. However, the extent and process of this damage to the downhole tools is intricate and less understood. In order to systematically evaluate and clarify this damage process for different types of drilling fluid contamination, this research uses a high-temperature drilling fluid damage device to simulate the damage caused to the casing/drilling tools by various drilling fluid under a field thermal gradient. The results show that the drilling fluid residues are mainly solid-phase particles and organic components. The degree of casing/tool damage decreases with an increase in bottom hole temperature, and the casing/tool is least damaged within a temperature range of 150–180 ℃. Moreover, the surface of the casing/tool damaged by different types of drilling fluid shows different roughness, and the wettability of drilling fluid on the casing/tool surface increases with an increase in the degree of roughness. Oil-based drilling fluid have the strongest adhesion contamination on casing/drilling tools. In contrast, polysulfonated potassium drilling fluid and super-micro drilling fluid have the most potent erosion damage on casing/drilling tools. By analyzing the damage mechanism, it was established that the damage was mainly dominated by the abrasive wearing from solid-phase particles in concert with corrosion ions in drilling fluid, with solids producing many abrasion marks and corrosive ions causing a large number of pits. Clarifying drilling fluid's contamination and damage mechanism is significant in guiding the wellbore cleaning process and cutting associated costs.

Open Access Original Paper Issue
Intelligent responsive self-assembled micro-nanocapsules: Used to delay gel gelation time
Petroleum Science 2024, 21(4): 2433-2443
Published: 23 April 2024
Abstract PDF (4.4 MB) Collect
Downloads:4

In the application of polymer gels to profile control and water shutoff, the gelation time will directly determine whether the gel can “go further” in the formation, but the most of the methods for delaying gel gelation time are complicated or have low responsiveness. There is an urgent need for an effective method for delaying gel gelation time with intelligent response. Inspired by the slow-release effect of drug capsules, this paper uses the self-assembly effect of gas-phase hydrophobic SiO2 in aqueous solution as a capsule to prepare an intelligent responsive self-assembled micro-nanocapsules. The capsule slowly releases the cross-linking agent under the stimulation of external conditions such as temperature and pH value, thus delaying gel gelation time. When the pH value is 2 and the concentration of gas-phase hydrophobic SiO2 particles is 10%, the gelation time of the capsule gel system at 30, 60, 90, and 120 ℃ is 12.5, 13.2, 15.2, and 21.1 times longer than that of the gel system without containing capsule, respectively. Compared with other methods, the yield stress of the gel without containing capsules was 78 Pa, and the yield stress after the addition of capsules was 322 Pa. The intelligent responsive self-assembled micro-nanocapsules prepared by gas-phase hydrophobic silica nanoparticles can not only delay the gel gelation time, but also increase the gel strength. The slow release of cross-linking agent from capsule provides an effective method for prolongating the gelation time of polymer gels.

Open Access Original Paper Issue
The deposition of asphaltenes under high-temperature and high-pressure (HTHP) conditions
Petroleum Science 2023, 20(1): 611-618
Published: 08 September 2022
Abstract PDF (2.1 MB) Collect
Downloads:3

In this work, the factors affecting asphaltenes deposition in high-temperature and high-pressure wells were studied using backscattered light and PVT equipment customized to suit the well conditions. In an examination of the intensity of backscattered light, it was revealed that there exists a linear relationship between temperature and asphaltene precipitation within a specific temperature range. Within this range, a decrease in temperature tends to accelerate asphaltene precipitation. However, the impacts of pressure and gas-oil ratio are more pronounced. The pressure depletion induces the asphaltenes to precipitate out of the solution, followed by the formation of flocs below the bubble point. In addition, an increase in the gas-oil ratio causes a more severe asphaltene deposition, shifting the location of asphaltenes to deep well sections.

Total 6