AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (2.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access | Just Accepted

K/Ce/Sm multiple-doped CaBi2Nb2O9 aurivillius-type ceramics used for high-temperature piezoelectric ultrasonic transducer

Chengxin Xu1,#, Junnan Wang1,#, Huajiang Zhou1, Jiageng Xu1, Zhi Zhou2, He Qi2, Jun Chen2, Yu Chen3( )

1 School of Mechanical Engineering, Chengdu University, Chengdu 610106, China

2 School of Materials Science and Engineering, Hainan University, Haikou, China

3 School of of Materials Science and Engineering, Xihua University, Chengdu 610039, China

# These authors contributed equally to this work.

Show Author Information

Abstract

Aurivillius-type CaBi2Nb2O9 (CBN) is attractive for high-temperature ultrasonic sensing owing to its high Curie temperature (TC ≈ 940 ℃). However, its weak piezoelectric response and loss of polarization alignment during thermal exposure limit its practical performance. Herein, K/Ce/Sm co-substitution at the Ca site was employed to modify the lattice structure, electrical transport, and domain morphology of CBN ceramics. Co-substitution reduced the orthorhombic distortion while preserving the orthorhombic framework. The optimized CBN-KCS-12 ceramic exhibited a piezoelectric coefficient d33 of 18 pC/N, a TC of approximately 933 ℃, and a ρdc resistivity of 2.59 × 106 Ω·cm at 650 ℃, approximately 18.5 times that of undoped CBN. The annealing temperature corresponding to 50% retention of the initial d₃₃ increased from 600 to 850 ℃, and CBN-KCS-12 retained approximately 44% of its initial d33 after annealing at 900 ℃. Piezoresponse force microscopy revealed larger block-like regions in CBN-KCS-12 compared with the fine stripe-like patterns in undoped CBN, with block-like contrast also observed after annealing at 900 ℃. The elastic modulus also increased from 30.1 to 33.8 GPa. Finally, a single-element ultrasonic transducer fabricated from CBN-KCS-12 produced clear pulse-echo signals from room temperature to 400 ℃, achieving a signal-to-noise ratio above 36 dB and a -6 dB fractional bandwidth of approximately 42% at 400 °C. These results demonstrate the potential of multi-element A-site co-substitution for improving CBN ceramics for high-temperature ultrasonic applications.

Electronic Supplementary Material

Download File(s)
JAC1409-ESM.pdf (1.6 MB)

References

【1】
【1】
 
 
Journal of Advanced Ceramics

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Xu C, Wang J, Zhou H, et al. K/Ce/Sm multiple-doped CaBi2Nb2O9 aurivillius-type ceramics used for high-temperature piezoelectric ultrasonic transducer. Journal of Advanced Ceramics, 2026, https://doi.org/10.26599/JAC.2026.9221409

45

Views

3

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 29 September 2026
Revised: 29 October 2026
Accepted: 14 November 2026
Available online: 16 November 2026

© The Author(s) 2026.

The articles published in this open access journal are distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/).