AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (10.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access | Online First

Electrical insulation enhancement of the Al2O3 composite films at high temperature by oxygen vacancy suppression

Zhichun Liu1,2, Junyang Chen1, Heng Wang1, Haigang Wang2, Mingyang Kong2, Zhe Yang2, Libo Gao3, Yang Zhao3, Zhixuan Su1( ), Mao Chen4,5 ( ), Bingbing Fan5,6, Zhenyin Hai1, Chenyang Xue1, Enbo Feng7, Junsheng Liang2( )
School of Aerospace Engineering, Xiamen University, Xiamen 361005, China
Key Laboratory for Micro/Nano Technology and System of Liaoning Province, Dalian University of Technology, Dalian 116023, China
School of Intelligent Manufacturing (Pen-Tung Sah Institute of Micro-Nano Science and Technology), Xiamen University, Xiamen 361105, China
Luoyang Industrial Technology Research Institute, Zhengzhou University, Luoyang 471100, China
School of Materials Science and Engineering, Zhengzhou University, Zhengzhou 450001, China
Department of Engineering, Faculty of Environment, Science and Economy, University of Exeter, Exeter EX4 4QF, UK
State Key Laboratory of Industrial Control Technology, East China University of Science and Technology, Shanghai 200237, China
Show Author Information

Abstract

Electrical insulation films are critical for the reliable operation of ultrahigh-temperature thin-film sensors (UTTSs) at elevated temperatures. However, the resistance of the insulation film easily declines at high temperatures due to the formation of oxygen vacancies and through-type defects, which will affect the long-term stability and reliability of the UTTSs. Here, we report a novel gas–liquid phase composite strategy to fabricate Al2O3 composite insulation films. An Al2O3 bottom film was first deposited by liquid-phase electrohydrodynamic jet printing, followed by the deposition of a dense Al2O3 film by magnetron sputtering. This design not only effectively repairs through-type defects in the liquid-phase film and improves overall densification but also suppresses the formation of oxygen vacancies in films. The gas-phase Al2O3 (G-Al2O3)/liquid-phase Al2O3 (L-Al2O3) composite film exhibits a smooth surface with substantially reduced microcracks and porosity. X-ray photoelectron spectroscopy reveals a significantly lower relative oxygen vacancy level in the composite films than in the pure L-Al2O3 film. Consequently, the G-Al2O3/L-Al2O3 film achieves an insulation resistance of 44 kΩ at 1400 °C, an order of magnitude higher than that of the pure L-Al2O3 film. In addition, three thermal cycles between 800 and 1200 °C demonstrate excellent repeatability of the insulation resistance within this temperature range. Practically, the Al2O3 composite films were applied to thin-film strain gauges (TFSGs), and the TFSGs exhibited excellent performance at high temperatures.

Graphical Abstract

Electronic Supplementary Material

Download File(s)
JAC1397_ESM.pdf (1.1 MB)

References

【1】
【1】
 
 
Journal of Advanced Ceramics

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Liu Z, Chen J, Wang H, et al. Electrical insulation enhancement of the Al2O3 composite films at high temperature by oxygen vacancy suppression. Journal of Advanced Ceramics, 2026, https://doi.org/10.26599/JAC.2026.9221397

481

Views

51

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 25 June 2026
Revised: 20 September 2026
Accepted: 10 October 2026
Published: 20 November 2026
© The Author(s) 2026.

This is an open access article under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0, http://creativecommons.org/licenses/by/4.0/).