AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (4.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Original Paper | Open Access

Sand control mechanism of radial well filled with phase change material in hydrate reservoir

Xiao-Qiang Liua,b, Zhong-Xi Hanc, Zhi-Lin Luod, Hai-Long Lue( ), Ying Sunf( ), Qing Youa,b, Tian-Kui Guog, Zhan-Qing Qug
School of Energy Resources, China University of Geosciences (Beijing), Beijing, 10083, China
Beijing Key Laboratory of Unconventional Natural Gas Geological Evaluation and Development Engineering, China University of Geosciences (Beijing), Beijing, 10083, China
China Research Institute of Petroleum Exploration and Development, Beijing, 10083, China
Engineering Technology Research Institute of Southwest Oil & Gas Field Company, PetroChina, Chengdu, 610051, Sichuan, China
Beijing International Center for Gas Hydrate, School of Earth and Space Sciences, Peking University, Beijing, 100871, China
School of Advanced Material, Peking University Shenzhen Graduate School, Shenzhen, 518055, Guangdong, China
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao, 266580, shandong, China

Edited by Yan-Hua Sun

Show Author Information

Abstract

Radial well filled with phase change material has been proposed as a novel sand control method for hydrate exploitation. In order to reveal the sand control mechanism, CFD-DEM coupling method is applied to simulate the migration, settlement, and blockage processes of sand particles in the radial well. The obtained results indicate that three scenarios have been recognized for sand particles passing through sand control medium, based on the diameter ratio of sand control medium to sand particle (Dd): fully passing (Dd = 8.75–22.5), partially passing and partially blocked (Dd = 3.18–5.63), and completely blocked (Dd = 2.18–3.21). After being captured by the sand control medium, sand particles can block pores, which increases fluid flow resistance and causes a certain pressure difference in the radial well. The pressure in the radial well should be lower than the hydrate phase equilibrium pressure during sand control design, for the purpose of promoting hydrate decomposition, and sand capture. The length of the radial well should be optimized based on the reservoir pore pressure, production pressure difference, bottom hole pressure, and the pressure gradient in the radial well. It should be noticed that the sand control medium leads to a decrease in permeability after sand particles captured. Even the permeability is reduced to several hundred millidarcy, it is still sufficient to ensure the effective flow of gas and water after hydrate decomposition. Increasing fluid velocity reduces the blocking capacity of the sand control medium, mainly because of deterioration in bridging between sand particles.

References

【1】
【1】
 
 
Petroleum Science
Pages 2571-2582

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Liu X-Q, Han Z-X, Luo Z-L, et al. Sand control mechanism of radial well filled with phase change material in hydrate reservoir. Petroleum Science, 2024, 21(4): 2571-2582. https://doi.org/10.1016/j.petsci.2024.04.008

668

Views

5

Downloads

9

Crossref

9

Web of Science

10

Scopus

1

CSCD

Received: 23 July 2023
Revised: 15 April 2024
Accepted: 15 April 2024
Published: 16 April 2024
© 2024 The Authors.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).