AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (13.9 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Comparative analysis of microstructure, mechanical, and corrosion properties of biodegradable Mg-3Y alloy prepared by selective laser melting and spark plasma sintering

P. Minárika,b( ), M. Zemkováa, S. Šašeka, J. Dittricha, M. Knapeka, F. Lukáča,c, D. Koutnýd, J. Jarošd, R. Krála
Faculty of Mathematics and Physics, Charles University, Ke Karlovu 5, Praha 121 16, Czech Republic
Research Centre, University of Žilina, Univerzitná 8215/1, Žilina 010 26, Slovakia
Institute of Plasma Physics of the Czech Academy of Sciences, Za Slovankou 1782/3, 182 00 Praha 8, Czech Republic
Institute of Machine and Industrial Design, Brno University of Technology, Technická 2896/2, Brno 616 69, Czech Republic
Show Author Information

Abstract

This work explored possibilities of biodegradable magnesium alloy Mg-3Y preparation by two modern powder metallurgy techniques – spark plasma sintering (SPS) and selective laser melting (SLM). The powder material was consolidated by both methods utilising optimised parameters, which led to very low porosity (~0.3%) in the SLM material and unmeasurably low porosity in the SPS material. The main aim of the study was the thorough microstructure characterisation and interrelation between the microstructure and the functional properties, such as mechanical strength, deformability, and corrosion resistance. Both materials showed comparable strength of ~110 MPa in tension and compression and relatively good deformability of ~9% and ~21% for the SLM and SPS materials, respectively. The corrosion resistance of the SPS material in 0.1 M NaCl solution was superior to the SLM one and comparable to the conventional extruded material. The digital image correlation during loading and the cross-section analysis of the corrosion layers revealed that the residual porosity and large strained grains have the dominant negative effect on the functional properties of the SLM material. On the other hand, one of the primary outcomes of this study is that the SPS consolidation method is very effective in the preparation of the W3 biodegradable alloy, resulting in material with convenient mechanical and degradation properties that might find practical applications.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 1496-1510

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Minárik P, Zemková M, Šašek S, et al. Comparative analysis of microstructure, mechanical, and corrosion properties of biodegradable Mg-3Y alloy prepared by selective laser melting and spark plasma sintering. Journal of Magnesium and Alloys, 2024, 12(4): 1496-1510. https://doi.org/10.1016/j.jma.2024.04.018

655

Views

10

Downloads

15

Crossref

12

Web of Science

14

Scopus

0

CSCD

Received: 29 January 2024
Revised: 28 February 2024
Accepted: 07 April 2024
Published: 27 April 2024
© 2024 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University