AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (15.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Individual effect of Y and Nd on the microstructure formation of Mg-Y-Nd alloys processed by severe plastic deformation and their effect on the subsequent mechanical and corrosion properties

Mária Zemkováa, Peter Minárika,b( ), Jan Dittricha, Jan Bohlenc, Robert Krála
Charles University, Department of Physics of Materials, Ke Karlovu 5, 12116, Prague, Czechia
University of Žilina, Research Centre, Univerzitná 8215/1, Žilina, 01026, Slovakia
Institute of Material and Process Design, Helmholtz-Zentrum Hereon, 21502, Geesthacht, Germany
Show Author Information

Abstract

This work investigated the effect of sole yttrium and neodymium alloying on the microstructure formation during severe plastic deformation by equal channel angular pressing (ECAP) and an impact on the mechanical strength and corrosion resistance of binary Mg-3Y and Mg-3Nd alloys. The results are compared with a ternary Mg-4Y-3Nd alloy, which represents a simplified version of the commercially successful WE43 alloy. The extensive study comprises a thorough microstructural analysis performed by scanning and transmission electron microscopy, including electron backscatter diffraction and texture analysis performed by X-ray diffraction. It is shown that the presence of Nd primarily caused precipitation during the processing of the Mg-3Nd alloy, while Y remained dissolved in the magnesium matrix in the Mg-3Y alloy. This difference resulted in a significantly smaller average grain size in the Mg-3Y alloy (~0.77 nm) than in the Mg-3Nd alloy (~1.3 µm) after the final step of the processing and formation of a slightly different texture. Consequently, the composition and the processing affected the mechanical and corrosion properties of the investigated materials, measured by compression deformation tests, microhardness measurement, and electrochemical impedance spectroscopy. This study shows that the ECAP-processed W3 sample exhibits a surprisingly good combination of ultrafine-grain structure, weak crystallographic texture, high strength, and high corrosion resistance compared with the other investigated samples. These attributes make this material very interesting for utilisation in the industry and/or medicine.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 509-521

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Zemková M, Minárik P, Dittrich J, et al. Individual effect of Y and Nd on the microstructure formation of Mg-Y-Nd alloys processed by severe plastic deformation and their effect on the subsequent mechanical and corrosion properties. Journal of Magnesium and Alloys, 2023, 11(2): 509-521. https://doi.org/10.1016/j.jma.2023.01.012

501

Views

3

Downloads

41

Crossref

34

Web of Science

37

Scopus

5

CSCD

Received: 07 August 2022
Revised: 19 December 2022
Accepted: 13 January 2023
Published: 26 February 2023
© 2023 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University