AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Article Link
Collect
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Correcting distortions of thin-walled machined parts by machine hammer peening

Aitor MADARIAGAa( ), Mikel CUESTAb, Gorka ORTIZ-DE-ZARATEb, Eneko SÁENZ-DE-ARGANDOÑAb, Denis SORIANOb, Michael B. PRIMEc, Pedro José ARRAZOLAb
Department of Materials, University of Manchester, Oxford Road, Manchester M13 9PL, United Kingdom
Mechanical and Industrial Production Department, Faculty of Engineering, Mondragon Unibertsitatea, Arrasate 20500, Spain
Los Alamos National Laboratory, Los Alamos, New Mexico, USA
Show Author Information

Abstract

Thin-walled aerostructural components frequently get distorted after the machining process. Reworking to correct distortions or eventually rejecting parts significantly increases the cost. This paper proposes a new approach to correct distortions in thin-walled components by strategically applying hammer peening on target surfaces of a machined component. Aluminium alloy 7475-T7351 was chosen for this research. The study was divided in two stages. First, the residual stresses (RS) induced by four different pneumatic hammer peening conditions (modifying the stepover distance and initial offset) were characterised in a test coupon, and one of the conditions was selected for the next stage. In the second stage, a FEM model was used to predict distortions caused by machining in a representative workpiece. Then, the RS induced by hammer peening were included in an FEM model to define two hammer peening strategies (varying the coverage area) to analyse the capability to reduce distortions. Two workpieces were machined and then treated with the simulated hammer peening strategies for experimental validation. Results in the test coupon showed that pneumatic hammer peening can generate high compressive RS (-50 to −350 MPa) up to 800 μm depth, with their magnitude increasing with a reduced stepover distance. Application of hammer peening over 4 % of the surface of the representative workpiece reduced the machining-induced distortions by 37 %, and a coverage area of 100 % led to and overcorrection by a factor of five. This confirms that hammer peening can be strategically applied (in target areas and changing the percentage of coverage) to correct low or severe distortions.

References

【1】
【1】
 
 
Chinese Journal of Aeronautics
Pages 439-453

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
MADARIAGA A, CUESTA M, ORTIZ-DE-ZARATE G, et al. Correcting distortions of thin-walled machined parts by machine hammer peening. Chinese Journal of Aeronautics, 2024, 37(6): 439-453. https://doi.org/10.1016/j.cja.2023.10.023

891

Views

9

Crossref

7

Web of Science

8

Scopus

1

CSCD

Received: 06 June 2023
Revised: 28 August 2023
Accepted: 06 October 2023
Published: 31 October 2023
© 2023 Chinese Society of Aeronautics and Astronautics.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).