AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Article Link
Collect
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Efficient machining of a complex blisk channel using a disc cutter

Xiangyu LIa, Zhaoyu LIa, Dong HEa, Junxue RENb, Qian FENGc, Kai TANGa,d,e( )
Department of Mechanical and Aerospace Engineering, Hong Kong University of Science and Technology, Hong Kong 999077, China
Key Laboratory of High Performance Manufacturing for Aero Engine (Northwestern Polytechnical University), Ministry of Industry and Information Technology, Xi’an 710072, China
Xi’an Sanhang Power Technology Co., Ltd, Xi’an 710000, China
HKUST Shenzhen-Hong Kong Collaborative Innovation Research Institute, Futian, Shenzhen 518057, China
HKUST Shenzhen Research Institute, Shenzhen 518057, China

Peer review under responsibility of Editorial Committee of CJA.

Show Author Information

Abstract

For rough machining of a complex narrow cavity, e.g., a complex blisk channel on an aero-engine, the typically used cutting tools are the slender cylindrical cutter and conical cutter. Nevertheless, as neither of the two is particularly suited for rough machining, wherein the main purpose is to remove a large volume as quickly as possible, the machining efficiency is low, especially when the part materials are of hard-to-cut types (e.g., Titanium-alloy) for which it often takes days to rough machine a blisk. Fortunately, disc machining provides a new and efficient roughing solution, since a disc cutter with a large radius enables a much larger cutting speed and thus a larger material removal rate. However, due to the large radius of the disc cutter, its potential collision with narrow and twisted channels becomes a serious concern. In this paper, we propose a novel two-phase approach for efficiently machining a complex narrow cavity workpiece using a disc-shaped cutter, i.e., 3 + 2-axis disc-slotting of the channel by multiple layers (rough machining) + five-axis disc-milling of the freeform channel side surfaces (semi-finish machining). Both simulation and physical cutting experiments are conducted to assess the effectiveness and advantages of the proposed method. The experimental results show that, with respect to a same cusp-height threshold on the channel side surfaces, the total machining time of the tested part by the proposed method is about only 36% of that by the conventional approach of plunging-milling (for roughing) plus milling by a slender cylindrical cutter (for semi-finishing).

Electronic Supplementary Material

Download File(s)
cja-37-1-414_ESM.pdf (2.5 MB)

References

【1】
【1】
 
 
Chinese Journal of Aeronautics
Pages 414-437

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
LI X, LI Z, HE D, et al. Efficient machining of a complex blisk channel using a disc cutter. Chinese Journal of Aeronautics, 2024, 37(1): 414-437. https://doi.org/10.1016/j.cja.2023.04.017

955

Views

12

Crossref

13

Web of Science

11

Scopus

1

CSCD

Received: 26 December 2022
Revised: 17 January 2023
Accepted: 18 March 2023
Published: 20 April 2023
© 2023 Chinese Society of Aeronautics and Astronautics.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).