AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (2.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Anisotropic tribology and electrification properties of sliding-mode triboelectric nanogenerator with groove textures

Weixu YANG1( ), Jieyang WANG1, Xiaoli WANG2, Ping CHEN1
Department of Mechanical Engineering, University of Science and Technology Beijing, Beijing 100083, China
Department of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China
Show Author Information

Abstract

Sliding-mode triboelectric nanogenerator (S-TENG) is based on the coupling of triboelectrification and electrostatic induction, converting electrical energy from sliding motion. Introducing micro-textures into the sliding surface, and adjusting the angle between the texture and sliding direction (direction angle) may achieve performance anisotropy, which provides novel ideas for optimizing the tribology and electrification performance of S-TENG. To guide the performance optimization based on the anisotropy, in this paper, groove micro-textures were fabricated on the surface of S-TENG, and anisotropic tribology and electrification performance were obtained through changing the direction angle. Based on the surface analysis and after-cleaning tests, the mechanism of the anisotropy was explained. It is shown that the anisotropy of friction coefficient can be attributed to the changes of texture edge induced resistance and groove captured wear debris, while the voltage anisotropy is due to the variations of debris accumulated on the sliding interface and the resulting charge neutralization. Among the selected 0°–90° direction angles, S-TENG at angle of 90° exhibits relatively small stable friction coefficient and high open-circuit voltage, and thus it is recommended for the performance optimization. The open-circuit voltage is not directly associated with the friction coefficient, but closely related to the wear debris accumulated on the sliding interface. This study presents a simple and convenient method to optimize the performance of S-TENG, and help understand the correlation between its tribology and electrical performance.

Graphical Abstract

Electronic Supplementary Material

Download File(s)
40544_0861_ESM.pdf (1.4 MB)

References

【1】
【1】
 
 
Friction
Pages 1828-1837

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
YANG W, WANG J, WANG X, et al. Anisotropic tribology and electrification properties of sliding-mode triboelectric nanogenerator with groove textures. Friction, 2024, 12(8): 1828-1837. https://doi.org/10.1007/s40544-024-0861-z

1252

Views

146

Downloads

18

Crossref

17

Web of Science

18

Scopus

2

CSCD

Received: 27 December 2022
Revised: 30 May 2023
Accepted: 18 December 2023
Published: 07 May 2024
© The author(s) 2023.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.