AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (3.7 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article

Control of Phase Separation and Crystallization for High-Efficiency and Mechanically Deformable Organic Solar Cells

Zicheng Ding1 ( )Yi Zhang1Yueling Su1Yin Wu1Yanchun Han2 Kui Zhao1 ( )Shengzhong (Frank) Liu1,3 ( )
Key Laboratory of Applied Surface and Colloid Chemistry, Ministry of Education, Shaanxi Key Laboratory for Advanced Energy Devices, Shaanxi Engineering Lab for Advanced Energy Technology, School of Materials Science and Engineering, Shaanxi Normal University, Xi’an 710119, China
State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun 130022, China
Dalian National Laboratory for Clean Energy, iChEM, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian 116023, China
Show Author Information

Abstract

Stretchable organic solar cells (OSCs) have great potential as power sources for the next-generation wearable electronics. Although blending rigid photovoltaic components with soft insulating materials can easily endow the mechanical ductility of active layers, the photovoltaic efficiencies usually drops in the resulting OSCs. Herein, a high photovoltaic efficiency of 15.03% and a large crack-onset strain of 15.70% is simultaneously achieved based on a ternary blend consisting of polymer donor poly[(2,6-(4,8-bis(5-(2-ethylhexyl-3-fluoro)thiophen-2-yl)-benzo[1,2-b:4,5-b’]dithiophene))-alt-(5,5-(1’,3’-di-2-thienyl-5’,7’-bis(2-ethylhexyl)benzo[1’,2’-c:4,5-c’]dithiophene-4,8-dione)] (PM6), non-fullerene accepter 2,2’-((2Z,2’Z)-((12,13-bis(2-ethylhexyl)-3,9-diundecyl-12,13-dihydro-[1,2,5]thiadiazolo[3,4-e]thieno[2’’,3’’:4’,5’]thieno[2’,3’:4,5]pyrrolo[3,2-g]thieno[2’,3’:4,5]thieno[3,2-b]indole-2,10-diyl)bis(methanylylidene))bis(5,6-difluoro-3-oxo-2,3-dihydro-1H-indene-2,1-diylidene))dimalononitrile (Y6), and soft elastomer polystyrene-block-poly (ethylene-ran-butylene)-block-polystyrene (SEBS) through the control of phase separation and crystallization. By employing a high-boiling point solvent additive 1-chloronaphthalene (CN) with different solubilities for PM6 and Y6, the aggregation dynamics of PM6 and Y6 as well as the film solidification process are dramatically altered, allowing for the different molecular rearrangement and liquid–liquid phase separation evolution. Consequently, the ternary film with optimal CN content presents decreased SEBS domains and moderately improved molecular ordering of PM6 and Y6, enabling effective mechanical deformation and charge generation/transport. The revealed corrections between the film-formation process, film microstructure, and photovoltaic/mechanical characteristics in the ternary blend provide deep understanding of the morphology control toward highperformance stretchable OSCs.

Electronic Supplementary Material

Download File(s)
eem-6-5-e12421_ESM.docx (69 KB)

References

【1】
【1】
 
 
Energy & Environmental Materials

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Ding Z, Zhang Y, Su Y, et al. Control of Phase Separation and Crystallization for High-Efficiency and Mechanically Deformable Organic Solar Cells. Energy & Environmental Materials, 2023, 6(5). https://doi.org/10.1002/eem2.12421

708

Views

5

Downloads

36

Crossref

38

Web of Science

35

Scopus

1

CSCD

Received: 26 February 2022
Revised: 09 April 2022
Published: 28 April 2022
© 2022 Zhengzhou University.