AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (2.1 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Publishing Language: Chinese

Experiment and anti-scuffing design for aviation gear scuffing based on material, surface treatment and lubricant combinations

Jinxiao CHEN1, Peitang WEI1( ), Yanjun LI2, Huaiju LIU1, Caichao ZHU1
Chongqing University, The State Key Laboratory of Mechanical Transmissions, Chongqing 400044, China
AECC Sichuan Gas Turbine Establishment, Chengdu 610500, China
Show Author Information

Abstract

Gear scuffing occurring under high-temperature, high-speed, and heavy-load can significantly impair the performance of aviation engines. However, there is a lack of test data on the gear scuffing load-carrying capacity, and insufficient anti-scuffing design under the combined influences of materials, surface treatmentand lubricants. This study investigates the effects of different combinations of materials (9310, 18Cr2Ni4WA, 16Cr3NiWMoVNbE), surface treatments (grinding, shot peening, Micro-shot peening, dual shot peening, barrel finishing, dual shot peening + barrel finishing) and lubricants (4450, 555, 4106, 4010, 2197, 387, 560, Mobil jet oil Ⅱ) on the scuffing load-carrying capacity, and proposes an evaluation method based on the PVT limit (involving gear contact pressure P, sliding velocity V, and lubricant temperature T). The results indicate that the tribological system composed of 16Cr3NiWMoVNbE, barrel finishing treatment, and 555 lubricant (containing high-performance EP additives) exhibits relatively superior anti-scuffing performance, and its PVT limit is 39 721 MPa·(m/s)0.51·℃0.45. Additive type, lubricant viscosity, and surface roughness are identified as three main factors affecting gear scuffing within the parameter framework, accounting for 28.7%, 23.6%, and 14.9%, respectively. An anti-scuffing design formula was fitted using the Ordinary Least-Squares (OLS) model, with an average error of only 4.99% compared to experimental results, providing a theoretical support for gear anti-scuffing design.

CLC number: V216.3 Document code: A Article ID: 1000-6893(2025)04-430777-16

References

【1】
【1】
 
 
Acta Aeronautica et Astronautica Sinica

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
CHEN J, WEI P, LI Y, et al. Experiment and anti-scuffing design for aviation gear scuffing based on material, surface treatment and lubricant combinations. Acta Aeronautica et Astronautica Sinica, 2025, 46(4). https://doi.org/10.7527/S1000-6893.2024.30777

1117

Views

19

Downloads

0

Crossref

1

Scopus

0

CSCD

Received: 03 June 2024
Revised: 26 June 2024
Accepted: 24 July 2024
Published: 25 February 2025
© 2025 The Journal of Acta Aeronautica et Astronautica Sinica