AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (2.7 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access | Just Accepted

Monolithically integrated flexible multimodal healthcare electronics on perovskite piezoelectric thin film for human motion and physiological signal monitoring

Mookyum Kim1, Kangsan Lee2,3, Myeong Seok Ko2,3, Il Doh2,4, Seong-Gu Hong2,3,5 ( )

1 Department of Bio-Healthcare, Hwasung Medi-Science University, Gyeonggi-do 18274, Republic of Korea

2 Department of Precision Measurement Engineering, University of Science and Technology, Daejeon 34113, Republic of Korea

3 Convergence Research Center for Meta-Touch, Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea

4 Division of Biomedical Metrology, Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea

5 Division of Chemical and Material Metrology, Korea Research Institute of Standards and Science, Daejeon 34113, Republic of Korea

Show Author Information

Abstract

Integrating multiple sensing modalities into a compact, mechanically compliant platform is essential for wearable healthcare electronics aimed at monitoring human motion and physiological signals. However, conventional multimodal sensors typically rely on rigid, multilayered architectures that limit flexibility, increase fabrication complexity, and introduce mechanically vulnerable interfacial boundaries. Here, we present a monolithically integrated flexible multimodal healthcare electronics (f-MHE) platform fabricated on a perovskite piezoelectric thin film, enabling dual-parameter detection of pressure and temperature within a single-layer architecture. The platform integrates an interdigitated-electrode piezoelectric pressure sensor for pulse-wave detection and a serpentine thermoresistive temperature sensor for skin-temperature measurement. The monolithic design eliminates multilayer stacking and repeated alignment/etching steps, thereby simplifying fabrication, reducing interfacial boundaries, and enhancing mechanical integrity. As a result, the f-MHE achieves an ultrathin (<5 μm), mechanically compliant form factor that enables conformal attachment to curved and deformable surfaces, including human skin. The device exhibits a pressure sensitivity of 24.1 mV kPa–1 with a resolution of <0.1 kPa over 0.1–25 kPa, and a temperature sensitivity of 5.03 Ω °C–1 with a resolution of <0.1 °C over 25–45 °C. Robust linearity, stability, and durability are maintained under repeated mechanical deformation. Multimodal sensing is further validated through real-time, simultaneous monitoring of pulse waves, respiration, and body motion. This work provides a structurally simple yet highly efficient and reliable strategy for multifunctional sensor integration and highlights the potential of monolithic thin-film platforms for next-generation wearable health monitoring.

Graphical Abstract

References

【1】
【1】
 
 
Nano Research

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Kim M, Lee K, Seok Ko M, et al. Monolithically integrated flexible multimodal healthcare electronics on perovskite piezoelectric thin film for human motion and physiological signal monitoring. Nano Research, 2026, https://doi.org/10.26599/NR.2026.94909204

265

Views

16

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 19 May 2026
Revised: 03 August 2026
Accepted: 19 September 2026
Available online: 19 September 2026

© The Author(s) 2026. Published by Tsinghua University Press.

This is an open access article under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0, https://creativecommons.org/licenses/by/4.0/)