AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (18.2 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access | Online First

Isotropic pressure-assisted defect regulation of PµSL-printed 5Y–ZrO2 for high-reliability ultrathin dental veneers

Wenhua Tong1,†, Yanru Shen1,†, Pengjie Zhang3,†, Chen Yang4, Ying Jiang4, Feng Wang4, Suwei Dai1, Shuyi Huang1, Zhankun Pan4, Jinhua Li4, Weiwei Li1, Yongsheng Zhou2, Yuchun Sun1, Lida Che3( ), Xiang Wang1( )
Center of Digital Dentistry, Department of Prosthodontics, Peking University School and Hospital of Stomatology & National Center for Stomatology & National Clinical Research Center for Oral Diseases & National Engineering Research Center of Oral Biomaterials and Digital Medical Devices & Beijing Key Laboratory of Digital Stomatology & NHC Key Laboratory of Digital Stomatology & Key Laboratory of Digital Stomatology, Chinese Academy of Medical Sciences & NMPA Key Laboratory for Dental Materials, Beijing 100081, China
Department of Prosthodontics, Peking University School and Hospital of Stomatology, National Center for Stomatology, National Engineering Research Center of Oral Biomaterials and Digital Medical Devices, National Clinical Research Center for Oral Disease, Beijing Key Laboratory of Digital Stomatology, Research Center of Engineering and Technology for Computerized Dentistry, Ministry of Health, Beijing 100081, China
CISRI HIPEX Technology Co., Ltd., Beijing 100081, China
BMF Nano Material Technology Co., Ltd., Shenzhen 518017, China

† Wenhua Tong, Yanru Shen, and Pengjie Zhang contributed equally to this work.

Show Author Information

Abstract

Projection microstereolithography (PμSL) enables individualized zirconia ceramic restorations with complex freeform geometries and hundred-micrometer-scale thicknesses. However, PμSL-printed ceramics often retain residual porosity, interlayer heterogeneity, and printing-induced defects after debinding, which limits full densification by conventional pressureless sintering. This limitation is particularly critical for ultrathin veneers because their reduced load-bearing thickness and intricate anatomical geometries increase sensitivity to residual pores, layer defects, and dimensional deviations. Although higher sintering temperatures can promote diffusion-driven densification, they also accelerate grain coarsening, which is detrimental to 5Y–ZrO2 ceramics with limited transformation-toughening capability. Here, an isotropic pressure-assisted densification (iPAD) strategy was developed to regulate densification, defect chemistry, and microstructural uniformity in PμSL-printed 5Y–ZrO2 ceramics. In this process, the PµSL-printed specimens were first presintered and then further densified at elevated temperature under isotropic argon pressure to promote residual pore closure and improve the overall properties of the ceramics. The optimized iPAD-treated ceramics achieved a relative density of 98.90%, together with a flexural strength of 951.30±71.05 MPa, a Vickers hardness of 13.60±0.07 GPa, a fracture toughness of 4.06±0.30 MPa·m1/2 and a transmittance of 56.15%±1.11% at 555 nm. X-ray photoelectron spectroscopy (XPS), electron paramagnetic resonance (EPR) spectroscopy, transmission electron microscopy (TEM), and nanoindentation analyses reveal that the complete iPAD route results in a lower relative abundance of oxygen-vacancy-related defect states, reduces defect-related scattering centers, and improves nanoscale mechanical uniformity. For ~80 µm zirconia veneers, iPAD increased the fracture load by approximately 35% while maintaining high manufacturing accuracy. This work provides a defect-regulated densification paradigm for high-reliability PμSL-printed 5Y–ZrO2 ultrathin dental veneers.

Graphical Abstract

Electronic Supplementary Material

Download File(s)
JAC1383_ESM.pdf (548.8 KB)

References

【1】
【1】
 
 
Journal of Advanced Ceramics

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Tong W, Shen Y, Zhang P, et al. Isotropic pressure-assisted defect regulation of PµSL-printed 5Y–ZrO2 for high-reliability ultrathin dental veneers. Journal of Advanced Ceramics, 2026, https://doi.org/10.26599/JAC.2026.9221383

545

Views

54

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 06 July 2026
Revised: 12 September 2026
Accepted: 23 September 2026
Published: 16 November 2026
© The Author(s) 2026.

This is an open access article under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0, http://creativecommons.org/licenses/by/4.0/).