AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (3.8 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access | Just Accepted

From wall slip to intralayer shear: How surface asperities regulate friction in nanoconfined glycerol lubrication

Hang Li1, Chen Yang1, Shijing Xie2, Junqin Shi1,3 ( ), Xiaoli Fan1, Tengfei Cao1, Bin Zhao4, Jie Wang5, Shaowei Feng5

1 State Key Laboratory of Solidification Processing, Center of Advanced Lubrication and Seal Materials, Northwestern Polytechnical University, Xi’an, Shaanxi 710072, China

2 School of Mechanical and Electrical Engineering, Jinggangshan University, Ji'an 343009, China

3 Shandong Key Laboratory of High-Performance Special Alloys Intelligent Manufacturing and Application for Aerospace Equipment, Yantai, Shandong 264003, China

4 Xi’an Surface Material Protection Co., Ltd. Xi’an 710200, China

5 Beijing Institute of Astronautical Systems Engineering, Beijing 100076, China

Show Author Information

Abstract

Reducing friction at the nanoscale to minimize energy losses remains a significant challenge, as a substantial amount of energy is currently lost to friction and wear at tribological contact interfaces. Here, a comprehensive physical understanding is provided of how the transition from smooth to rough interfaces alters slip modes and energy dissipation pathways in high-viscosity glycerol. Through nonequilibrium molecular dynamics simulations of glycerol confined between hydroxylated SiO2 and CH-terminated surfaces with controlled asperity heights (0–6.4 Å) and film thicknesses (2–8 molecular layers), we identify that surface asperity height serves as the key regulator for slip mode transition. The results reveal that the wall slip of lubricating film appears on the non-polar CH-terminated surface with low roughness (h ≤ 3.2 Å). Because only discrete asperity heights were examined, we believe that the transition occurs between the tested values of 3.2 and 4.8 Å, with a high-dissipation mixed mode involving wall slip and intralayer shear first observed at h = 4.8 Å. This transition leads to dramatic increases in both friction coefficient and heat dissipation rate, which rise by more than two orders of magnitude as h increases from 0 to 6.4 Å. Force analysis demonstrates that the increased friction resistance primarily originates from the “wedge effect” and lubricant accumulation in the uphill regions. These findings suggest that for high-viscosity lubricants like glycerol, minimizing asperity height to promote 2D-like interfacial slip represents a robust strategy for achieving heterogeneous interface superlubricity.

Graphical Abstract

Electronic Supplementary Material

Download File(s)
F1337-ESM.pdf (8.1 MB)

References

【1】
【1】
 
 
Friction

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Li H, Yang C, Xie S, et al. From wall slip to intralayer shear: How surface asperities regulate friction in nanoconfined glycerol lubrication. Friction, 2026, https://doi.org/10.26599/FRICT.2026.9441337

22

Views

3

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 25 January 2026
Revised: 19 October 2026
Accepted: 10 November 2026
Available online: 11 November 2026

© The Author(s) 2026.

This is an open access article under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0, http://creativecommons.org/licenses/by/4.0/).