AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (1.5 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Publishing Language: Chinese | Open Access

The temperature control performance of deep-well fracturing equipment based on thermoelectric cooling technology

Weifeng Tang1, Youzhi Zhao1, Shuo Zhang1, Yongshen Ou1, Yongmin Zhang2, Wenxiao Chu1( ), Qiuwang Wang1
Key Laboratory of Thermo-Fluid Science and Engineering, Ministry of Education, Xi’an Jiaotong University, Xi’an 710049, China
State Key Laboratory of Electrical Insulation and Power Equipment, Xi’an Jiaotong University, Xi’an 710049, China
Show Author Information

Abstract

The exploration and exploitation of deep-well resources such as oil, gas, and geothermal energy are crucial for achieving the green and efficient conversion and utilization of energy and resources. However, the extreme high temperatures (>150 ℃) encountered downhole severely constrain the reliable operation of critical electronic components, including motors and power chips. Thermoelectric cooling, an active solid-state thermal control technology based on semiconductor direct energy conversion (electric-to-thermal), holds potential for thermal management in extreme environments due to the advantages such as compact structure and fast response. To investigate the performance limits and energy utilization efficiency of thermoelectric cooler(TEC) in deep-well high-temperature environments, this study systematically examined the temperature control characteristics of a TEC module under ambient temperatures ranging from 80 ℃ to 150 ℃ and a thermal load of 13.6 W, employing a combination of experimental measurements and numerical simulations. Experimental results demonstrate that under a 120 ℃ ambient temperature and 13.6 W thermal load, the TEC device can sustain a maximum temperature difference of 62.1 ℃ between its hot and cold ends, maintaining the cold-end surface temperature stably below 80 ℃. A reliable numerical prediction model was developed and validated. Simulation results revealed the dependence of the cold-end temperature on input current and demonstrated the independence of the maximum input current from the hot-end temperature. An approximate linear relationship between the maximum cooling capacity and the hot-end temperature was identified. Crucially for efficient energy utilization, the study confirmed the existence of an optimal operating current that minimizes the cold-end temperature, and this optimal current was found to be largely insensitive to the ambient temperature within the studied range. Furthermore, the analysis of the coefficient of performance (COP) indicated a trend where it initially increases with input current, reaches a peak, and then decreases. The magnitude of the COP increase was observed to be more significant at smaller temperature differences compared to larger ones. The findings suggest that enhancing hot-end heat dissipation and mitigating internal heat accumulation (due to the Joule effect) are effective strategies for improving the overall energy conversion performance of TECs, particularly under the large temperature differences characteristic of deep-well environments.

CLC number: O472; TB657

References

【1】
【1】
 
 
Journal of Northwest University (Natural Science Edition)
Pages 983-995

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Tang W, Zhao Y, Zhang S, et al. The temperature control performance of deep-well fracturing equipment based on thermoelectric cooling technology. Journal of Northwest University (Natural Science Edition), 2026, 56(5): 983-995. https://doi.org/10.16152/j.cnki.xdxbzr.2026-05-003

1

Views

0

Downloads

0

Crossref

0

CSCD

Received: 05 January 2026
Revised: 15 March 2026
Published: 25 October 2026
© The Editorial Department of Journal of Northwest University(Natural Science Edition)2026.

This is an open access article under the CC BY-NC-ND 4.0 license (https://creativecommons.org/licenses/by-nc-nd/4.0/).