AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (4.1 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Publishing Language: Chinese

Design of citrus identification and picking based on the Raspberry PI platform

Huanyu YANG1a,2, Wenjing HUANG1a( ), Yihua LI1b, Xiaogang DUAN3, Siyu KANG1a, Ziyi WANG1a, Xiaoyuan LUO1a, Mian JIANG4
School of Materials Science and Engineering
School of Logistics & Traffic, Central South University of Forestry & Technology, Changsha 410004, Hunan, China
School of Data Science, University of Science and Technology of China, Hefei 230026, Anhui, China
Central South Intelligence Collaborative Research Center, Changsha 410017, Hunan, China
School of Mechatronic Engineering and Automation, Foshan University, Foshan 528000, Guangdong, China
Show Author Information

Abstract

Objective

Based on the Raspberry PI platform, a portable citrus intelligent recognition and robot picking system were designed to provide a theoretical and experimental basis for reducing labor force and mechanical intelligence in citrus picking.

Method

The citrus data set was made, and the deep convolutional neural network (YOLOv4-tiny) was used to verify the validity of the data set. Based on the Raspberry PI platform combined with YOLOv4-tiny, a citrus intelligent recognition system was designed. The kinematic model and trajectory planning function of the five-degree-of-freedom manipulator were established, and the Raspberry PI development board, a camera and a small five-degree-of-freedom robot were used for the intelligent identification and picking of citruses.

Result

The recognition rate of the two-dimensional coordinates of citruses by the deep convolutional neural network (YOLOv4-tiny) model was 98%. After embedding Raspberry PI, combined with the similar triangle calculation method of the distance between the target and camera, the three-dimensional coordinates of citruses can be accurately identified (-3.2, 19.7, 16). After driving the mechanical arm to the position coordinate, the gripper clamp was made and the citrus can be picked up. After a total of 80 times of adjustment, the best time of mechanical arm movement was 1 000 ms, the best time of picking the end of the gripper was 500 ms, and the average angle of picking the end of the gripper was -60 degrees, so that the picking speed was appropriate without jitter. 20 harvest tests were conducted, and the average successful capture rate reached more than 90%.

Conclusion

The depth recognition and picking system based on the Raspberry PI platform can realize the recognition and accurate picking of three-dimensional coordinates of citruses, which provides a certain theoretical basis and experimental reference for intelligent citrus picking.

CLC number: S776.22+2;TP242 Document code: A Article ID: 1673-923X(2023)08-0192-10

References

【1】
【1】
 
 
Journal of Central South University of Forestry & Technology
Pages 192-201

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
YANG H, HUANG W, LI Y, et al. Design of citrus identification and picking based on the Raspberry PI platform. Journal of Central South University of Forestry & Technology, 2023, 43(8): 192-201. https://doi.org/10.14067/j.cnki.1673-923x.2023.08.019

702

Views

5

Downloads

0

Crossref

1

CSCD

Received: 08 February 2023
Published: 25 August 2023
© 2023 Journal of Central South University of Forestry & Technology