AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (6.4 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research paper | Publishing Language: Chinese | Open Access

Microstructure and tensile properties of diffusion bonded Ti150/Ti180 high temperature titanium alloys

Haishui REN1( ), Juan LI2, Yaoyong CHENG1, Zhiliang ZHAI1, Junfeng HUAI1
Welding and Plastic Forming Division,AECC Beijing Institute of Aeronautical Materials,Beijing 100095,China
Key Laboratory of Advanced Titanium Alloys,AECC Beijing Institute of Aeronautical Materials,Beijing 100095,China
Show Author Information

Abstract

To meet the manufacturing requirements for bimetallic or dual-performance components, the effects of various joining parameters and interlayer materials on the microstructure and tensile properties of diffusion-bonded Ti150/Ti180 joints are investigated. Microstructure and fracture surface of the joints are systematically studied using optical microscope, scanning electron microscopy, energy spectrum and X-ray diffractometer. Tensile properties of the joints are tested by universal testing machine. The results show that sound metallurgical bonding at the interface is achieved without an interlayer at bonding temperatures ranging from 800 ℃ to 900 ℃. Moreover, as the bonding temperature increases, the joint tensile strength gradually improves. Under the condition of 900 ℃/1 h/15 MPa, the joint achieves tensile strengths of 941 MPa at room temperature and 609 MPa at 450 ℃, corresponding to 86.2% and 81.3% of Ti150 alloy, respectively. However, the joint plasticity remains low. When Ti foil is used as the interlayer, residual Ti foil is observed in the joint under the condition of 900 ℃/10 MPa/2 h, indicating insufficient diffusion between the Ti foil and the base metals. The tensile strengths of these joints are comparable to those of joints bonded without an interlayer. When Ti55 titanium alloy is employed as the interlayer, the joint tensile strength reaches 992 MPa after bonding at 930 ℃/15 MPa/1 h, approximately 90.8% of Ti150 alloy, and the joint plasticity is also improved. Nevertheless, the tensile strength at 450 ℃ remains at a level similar to that of the other joints.

CLC number: V252.2;TG454 Document code: A Article ID: 1005-5053(2026)11-0046-09

References

【1】
【1】
 
 
Journal of Aeronautical Materials
Pages 46-54

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
REN H, LI J, CHENG Y, et al. Microstructure and tensile properties of diffusion bonded Ti150/Ti180 high temperature titanium alloys. Journal of Aeronautical Materials, 2026, 46(11): 46-54. https://doi.org/10.11868/j.issn.1005-5053.2026.000020

1

Views

0

Downloads

0

Crossref

0

Scopus

0

CSCD

Received: 26 January 2026
Accepted: 13 July 2026
Published: 15 November 2026
© Journal of Aeronautical Materials 2026.

This is an open access article under the CC BY-NC license (http://creativecommons.org/licenses/by-nc/4.0/).