AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (82.5 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Enhancing fatigue performance of AZ31 magnesium alloy components fabricated by cold metal transfer-based wire arc directed energy deposition through LPB

Shambhu Kumar Manjhi, Srikanth Bontha, A.S.S. Balan( )
Department of Mechanical Engineering, National Institute of Technology Karnataka, Surathkal, Srinivasanagar, Mangalore, Karnataka 575 025, India
Show Author Information

Abstract

Cold Metal Transfer-Based Wire Arc Directed Energy Deposition (CMT-WA-DED) presents a promising avenue for the rapid fabrication of components crucial to automotive, shipbuilding, and aerospace industries. However, the susceptibility to fatigue of CMT-WA-DED-produced AZ31 Mg alloy components has impeded their widespread adoption for critical load-bearing applications. In this study, a comprehensive investigation into the fatigue behaviour of WA-DED-fabricated AZ31 Mg alloy has been carried out and compared to commercially available wrought AZ31 alloy. Our findings indicate that the as-deposited parts exhibit a lower fatigue life than wrought Mg alloy, primarily due to poor surface finish, tensile residual stress, porosity, and coarse grain microstructure inherent in the WA-DED process. Low Plasticity Burnishing (LPB) treatment is applied to mitigate these issues, which induce significant plastic deformation on the surface. This treatment resulted in a remarkable improvement of fatigue life by 42%, accompanied by a reduction in surface roughness, grain refinement and enhancement of compressive residual stress levels. Furthermore, during cyclic deformation, WA-DED specimens exhibited higher plasticity and dislocation density compared to both wrought and WA-DED + LPB specimens. A higher fraction of Low Angle Grain Boundaries (LAGBs) in WA-DED specimens contributed to multiple crack initiation sites and convoluted crack paths, ultimately leading to premature failure. In contrast, wrought and WA-DED + LPB specimens displayed a higher percentage of High Angle Grain Boundaries (HAGBs), which hindered dislocation movement and resulted in fewer crack initiation sites and less complex crack paths, thereby extending fatigue life. These findings underscore the effectiveness of LPB as a post-processing technique to enhance the fatigue performance of WA-DED-fabricated AZ31 Mg alloy components. Our study highlights the importance of LPB surface treatment on AZ31 Mg components produced by CMT-WA-DED to remove surface defects, enabling their widespread use in load-bearing applications.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 1638-1662

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Manjhi SK, Bontha S, Balan A. Enhancing fatigue performance of AZ31 magnesium alloy components fabricated by cold metal transfer-based wire arc directed energy deposition through LPB. Journal of Magnesium and Alloys, 2024, 12(4): 1638-1662. https://doi.org/10.1016/j.jma.2024.04.016

701

Views

6

Downloads

20

Crossref

18

Web of Science

19

Scopus

0

CSCD

Received: 19 February 2024
Revised: 11 April 2024
Accepted: 15 April 2024
Published: 27 April 2024
© 2024 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University