AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (8.5 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Optimization of chemistry and process parameters for control of intermetallic formation in Mg sludges

Y. Fua, G.G. Wangb( ), A. Hua, Y. Lia, K.B. Thackerb, J.P. Weilerb, H. Hua( )
Department of Mechanical, Automotive and Materials Engineering, University of Windsor, 401 Sunset Ave, Windsor, Ontario N9B 3P4, Canada
Global Technology Centre, Meridian Lightweight Technologies, 25 MacNab Ave, Strathroy, Ontario N7G 4H6, Canada
Show Author Information

Abstract

Intermetallic formation in sludge during magnesium (Mg) melting, holding and high pressure die casting practices is a very important issue. But, very often it is overlooked by academia, original equipment manufacturers (OEM), metal ingot producers and even die casters. The aim of this study was to minimize the intermetallic formation in Mg sludge via the optimization of the chemistry and process parameters. The Al8Mn5 intermetallic particles were identified by the microstructure analysis based on the Al and Mn ratio. The design of experiment (DOE) technique, Taguchi method, was employed to minimize the intermetallic formation in the sludge of Mg alloys with various chemical compositions of Al, Mn, Fe, and different process parameters, holding temperature and holding time. The sludge yield (SY) and intermetallic size (IS) was selected as two responses. The optimum combination of the levels in terms of minimizing the intermetallic formation were 9 wt.% Al, 0.15 wt.%Mn, 0.001 wt.% (10 ppm) Fe, 690 ℃ for the holding temperature and holding at 30 mins for the holding time, respectively. The best combination for smallest intermetallic size were 9 wt.% Al, 0.15 wt.%Mn, 0.001 wt.% (10 ppm) Fe, 630 ℃ for the holding temperature and holding at 60 mins for the holding time, respectively. Three groups of sludge factors, Chemical Sludge (CSF), Physical Sludge (PSF) and Comprehensive Sludge Factors (and CPSF) were established for prediction of sludge yields and intermetallic sizes in Al-containing Mg alloys. The CPSF with five independent variables including both chemical elements and process parameters gave high accuracy in prediction, as the prediction of the PSF with only the two processing parameters of the melt holding temperature and time showed a relatively large deviation from the experimental data. The Chemical Sludge Factor was primarily designed for small ingot producers and die casters with a limited melting and holding capacity, of which process parameters could be fixed easily. The Physical Sludge Factor could be used for mass production with a single type of Mg alloy, in which the chemistry fluctuation might be negligible. In large Mg casting suppliers with multiple melting and holding furnaces and a number of Mg alloys in production, the Comprehensive Sludge Factor should be implemented to diminish the sludge formation.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 1431-1448

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Fu Y, Wang G, Hu A, et al. Optimization of chemistry and process parameters for control of intermetallic formation in Mg sludges. Journal of Magnesium and Alloys, 2024, 12(4): 1431-1448. https://doi.org/10.1016/j.jma.2024.04.011

713

Views

3

Downloads

0

Crossref

0

Web of Science

0

Scopus

0

CSCD

Received: 29 November 2023
Revised: 02 April 2024
Accepted: 06 April 2024
Published: 20 April 2024
© 2024 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University