AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (20.6 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Effects of homogenization temperature on microstructure and mechanical properties of high-speed-extruded Mg–5Bi–3Al alloy

Jae Won Chaa, Sang-Cheol Jina, Jae-Gil Jungb, Sung Hyuk Parka( )
School of Materials Science and Engineering, Kyungpook National University, 80 Daehakro, Daegu 41566, Republic of Korea
Advanced Metals Division, Korea Institute of Materials Science, Changwon 51508, Republic of Korea
Show Author Information

Abstract

This study investigates the effects of billet homogenization temperature on the dynamic recrystallization behavior during high-speed extrusion and resultant microstructure and tensile properties of the Mg–5Bi–3Al (BA53, wt%) alloy. Two billets homogenized at 350 and 450 ℃ (350H and 450H billets) are extruded at a high speed of 69 m/min. The 350H billet has a relatively smaller grain size and a higher abundance of fine Mg3Bi2 particles compared to the 450H billet. During extrusion of the 350H billet, enhanced dynamic recrystallization occurs as a result of its finer grains and abundance of particles, while the growth of recrystallized grains is suppressed by the grain-boundary pinning effect of particles. Ultimately, the extruded 350H material is characterized by smaller grains, relatively greater number of Mg3Bi2 particles, and a higher internal strain energy than the extruded 450H material. The tensile strength of the extruded 350H material is higher than that of the extruded 450H material owing to stronger grain-boundary hardening, particle hardening, and strain hardening effects. The extruded 350H material also exhibits a higher tensile elongation as its smaller grains inhibit the formation of crack-inducing undesirable twins during tension. The results from this study demonstrate that a decrease in the homogenization temperature from 450 to 350 ℃ leads to improved strength and ductility in the high-speed-extruded BA53 material.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 2833-2846

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Cha JW, Jin S-C, Jung J-G, et al. Effects of homogenization temperature on microstructure and mechanical properties of high-speed-extruded Mg–5Bi–3Al alloy. Journal of Magnesium and Alloys, 2022, 10(10): 2833-2846. https://doi.org/10.1016/j.jma.2021.07.007

432

Views

6

Downloads

62

Crossref

61

Web of Science

65

Scopus

0

CSCD

Received: 29 December 2020
Revised: 22 May 2021
Accepted: 05 July 2021
Published: 13 August 2021
© 2021 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University