AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (8.6 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91

M. Varatharajulua,b( ), Muthukannan Duraiselvama( ), M. Bhuvanesh Kumara,d, G. Jayaprakashc, N. Baskarc
Department of Production Engineering, National Institute of Technology, Tiruchirappalli 620015, Tamilnadu, India
Department of Mechanical Engineering, A. V. C. College of Engineering, Mannampandal, 609305, Tamilnadu, India
Department of Mechanical Engineering, Saranathan College of Engineering, Tiruchirapalli 620012, Tamilnadu, India
Department of Mechanical Engineering, Kongu Engineering College, Perundurai 638060, Tamilnadu, India
Show Author Information

Abstract

Magnesium (Mg) alloys are extensively used in the automotive and aircraft industries due to their prominent properties. The selection of appropriate process parameters is an important decision to be made because of the cost reduction and quality improvement. This decision entails the selection of suitable process parameters concerning various conflicting factors, so it has to be addressed with the Multiple Criteria Decision Making (MCDM) method. Therefore, this work addresses the MCDM problem through the TOPSIS (Technique for Order Preference by Similarity to Ideal Solution) and COPRAS (COmplex PRoportional ASsessment) methods. The assessment carried out in the material Mg AZ91 with the Solid Carbide (SC) drill bit. The dependent parameters like drilling time, burr height, burr thickness, and roughness are considered with the independent parameters like spindle speed and feed rate. Drilling alternatives are ranked using the above said two methods and the results are evaluated. The optimum combination was found on the basis of TOPSIS and COPRAS for simultaneous minimization of all the responses which is found with a spindle speed of 4540 rpm and a feed rate of 0.076 mm/rev. The identical sequencing order was observed in TOPSIS and COPRAS method. The empirical model was developed through Box-Behnken design for each response. Superior empirical model developed for drilling time which is 3.959 times accurate than the conventional equation. The trends of various dependents based on the heterogeneity of various independents are not identical, these complex mechanisms are identified and reported. The optimized results of the Desirability Function Approach are greater accordance with the TOPSIS and COPRAS top rank. The confirmation results are observed with lesser deviation suggesting the selection of the above independent parameters.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 2857-2874

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Varatharajulu M, Duraiselvam M, Kumar MB, et al. Multi criteria decision making through TOPSIS and COPRAS on drilling parameters of magnesium AZ91. Journal of Magnesium and Alloys, 2022, 10(10): 2857-2874. https://doi.org/10.1016/j.jma.2021.05.006

677

Views

8

Downloads

98

Crossref

87

Web of Science

108

Scopus

1

CSCD

Received: 03 February 2021
Revised: 05 April 2021
Accepted: 11 May 2021
Published: 27 June 2021
© 2021 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University