AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (8.4 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Improving thermal efficiency and stability of laser welding process for magnesium alloy by combining power modulation and subatmospheric pressure environment

State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
BIAS - Bremer Institut für angewandte Strahltechnik GmbH, Klagenfurter Straße 5, 28359 Bremen, Germany

✩ The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.

Show Author Information

Abstract

The laser welding (LW) process of highly reflective materials presents low thermal efficiency and poor stability. To solve the problem, the effects of subatmospheric environment on LW process, technological parameters in subatmospheric environment on weld formation and welding with sinusoidal modulation of laser power on the stability of LW process in subatmospheric environment were explored. The AZ31 magnesium (Mg) alloy was used as the test materials. The test result revealed that the weld penetration in subatmospheric environment can increase by more than ten times compared with that under normal pressure. After the keyhole depth greatly rises, significantly periodic local bulge is observed on the backwall surface of the keyhole and the position of the bulge shifts along the direction of the keyhole depth. Eventually, the hump-shaped surface morphology of the welded seam is formed; moreover, the weld width in local zones in the lower part of the welded seam remarkably grows. During LW in subatmospheric environment, the weld penetration can be further greatly increased through power modulation. Besides, power modulation can inhibit the occurrence of bulges in local zones on the backwall of the keyhole during LW in subatmospheric environment, thus further curbing the significant growth of the weld widths of hump-shaped welding beads and local zones in the lower part of welded seams. Finally, the mechanism of synchronously improving the thermal efficiency and stability of LW process of highly reflective materials through power modulation in subatmospheric environment was illustrated. This was conducted according to theoretical analysis of recoil pressure and observation results of dynamic behaviors of laser induced plasma clouds and keyholes in the molten pool through high speed photography.

References

【1】
【1】
 
 
Journal of Magnesium and Alloys
Pages 2788-2800

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Ning J, Na S-J, Zhang L-J, et al. Improving thermal efficiency and stability of laser welding process for magnesium alloy by combining power modulation and subatmospheric pressure environment. Journal of Magnesium and Alloys, 2022, 10(10): 2788-2800. https://doi.org/10.1016/j.jma.2021.02.005

554

Views

6

Downloads

34

Crossref

37

Web of Science

38

Scopus

4

CSCD

Received: 30 September 2020
Revised: 28 December 2020
Accepted: 05 February 2021
Published: 09 April 2021
© 2021 Chongqing University.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/) Peer review under responsibility of Chongqing University