AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Article Link
Collect
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Full Length Article | Open Access

Micro-structure evolution, precipitation behavior and strengthening mechanism of Ni-Cr-Mo system steel fabricated via laser powder bed fusion and subsequent quenching control

Qing WANGa,b, Deyin KONGa, Shihui ZHOUa, Xingran LIa, Zhihui ZHANGa,c ( )
The Key Laboratory of Bionic Engineering (Ministry of Education), Jilin University, Changchun 130025, China
Weihai Institute for Bionic, Jilin University, Weihai 264402, China
State Key Laboratory of Automotive Simulation and Control, Jilin University, Changchun 130025, China

Peer review under responsibility of Editorial Committee of CJA

Show Author Information

Abstract

High-performance 24CrNiMo steel was fabricated using Laser Powder Bed Fusion (LPBF). Subsequent quenching treatment was applied and the influence of quenching temperatures on micro-structure evolution and properties was systematically characterised and analysed. The micro-structure of the as-built steel consisted of two parts. The first part comprised martensite with twins combined with ω-Fe nano-particles, and the second part consisted of lower bainite in the molten pool, as well as upper bainite, granular bainite and tempered martensite in the heat-affected zone. With the quenching temperatures varying from 800 °C to 950 °C, the micro-structure gradually transformed from acicular ferrite + martensite to tempered martensite +θ-Fe3C carbides, and the grain size exhibited noticeable growth. Moreover, quenching treatments could eliminate the anisotropy and inhomogeneity of the micro-structure. The rod-shaped nanosized η-Fe2C and θ-Fe3C precipitates were clearly observed, which were converted from ω-Fe and distributed at multiple angles in the lath. The size and number of nano-precipitates, triggered by the high self-tempering degree of martensite, gradually increased. The relationships among grain size, the twins, dislocation density and nano-precipitation and the dramatically improved performance of quenched samples were analysed using strengthening mechanisms. After quenching at 850 °C, the as-built 24CrNiMo steel attained ultra-high mechanical properties including hardness, Ultimate Tensile Strength (UTS), Elongation (El) and impact energy with values of 480.9 HV1, 1611.4 MPa, 9.8% and 42.8 J, respectively. Meanwhile, both the wear and thermal fatigue resistance increased by approximately 40%. This study demonstrated that LPBF-fabricated 24CrNiMo steel, with matching good performances, can be achieved using a subsequent one-step quenching process.

Electronic Supplementary Material

Download File(s)
cja-38-3-103221_ESM.pdf (18.5 MB)

References

【1】
【1】
 
 
Chinese Journal of Aeronautics

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
WANG Q, KONG D, ZHOU S, et al. Micro-structure evolution, precipitation behavior and strengthening mechanism of Ni-Cr-Mo system steel fabricated via laser powder bed fusion and subsequent quenching control. Chinese Journal of Aeronautics, 2025, 38(3). https://doi.org/10.1016/j.cja.2024.08.052

863

Views

4

Crossref

5

Web of Science

4

Scopus

1

CSCD

Received: 18 February 2024
Revised: 07 April 2024
Accepted: 28 April 2024
Published: 04 September 2024
© 2024 Chinese Society of Aeronautics and Astronautics.

This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).