AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (4.4 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Optimized Mask-RCNN model for particle chain segmentation based on improved online ferrograph sensor

Shuo WANGMiao WANTonghai WU( )Zichen BAIKunpeng WANG
Key Laboratory of Education Ministry for Modern Design and Rotor-Bearing System, Xi’an Jiaotong University, Xi’an 710049, China
Show Author Information

Abstract

Ferrograph-based wear debris analysis (WDA) provides significant information for wear fault analysis of mechanical equipment. After decades of offline application, this conventional technology is being driven by the online ferrograph sensor for real-time wear state monitoring. However, online ferrography has been greatly limited by the low imaging quality and segmentation accuracy of particle chains when analyzing degraded lubricant oils in practical applications. To address this issue, an integrated optimization method is developed that focuses on two aspects: the structural re-design of the online ferrograph sensor and the intelligent segmentation of particle chains. For enhancing the imaging quality of wear particles, the magnetic pole of the online ferrograph sensor is optimized to enable the imaging system directly observe wear particles without penetrating oils. Furthermore, a light source simulation model is established based on the light intensity distribution theory, and the LED installation parameters are determined for particle illumination uniformity in the online ferrograph sensor. On this basis, a Mask-RCNN-based segmentation model of particle chains is constructed by specifically establishing the region of interest (ROI) generation layer and the ROI align layer for the irregular particle morphology. With these measures, a new online ferrograph sensor is designed to enhance the image acquisition and information extraction of wear particles. For verification, the developed sensor is tested to collect particle images from different degraded oils, and the images are further handled with the Mask-RCNN-based model for particle feature extraction. Experimental results reveal that the optimized online ferrography can capture clear particle images even in highly-degraded lubricant oils, and the illumination uniformity reaches 90% in its imaging field. Most importantly, the statistical accuracy of wear particles has been improved from 67.2% to 94.1%.

References

【1】
【1】
 
 
Friction
Pages 1194-1213

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
WANG S, WAN M, WU T, et al. Optimized Mask-RCNN model for particle chain segmentation based on improved online ferrograph sensor. Friction, 2024, 12(6): 1194-1213. https://doi.org/10.1007/s40544-023-0800-4

781

Views

57

Downloads

14

Crossref

10

Web of Science

14

Scopus

1

CSCD

Received: 14 March 2023
Revised: 27 June 2023
Accepted: 07 July 2023
Published: 20 December 2023
© The author(s) 2023.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.