AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (5.6 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Synergistic tribological effect between polyisobutylene succinimide-modified molybdenum oxide nanoparticle and zinc dialkyldithiophosphate for reducing friction and wear of diamond-like carbon coating under boundary lubrication

Shuoshuo CHEN, Ningning SONG, Shengmao ZHANG( ), Yujuan ZHANG( ), Laigui YU, Pingyu ZHANG
National & Local Joint Engineering Research Center for Applied Technology of Hybrid Nanomaterials, Henan University, Kaifeng 475004, China
Show Author Information

Abstract

Organic molybdenum lubricant additive like molybdenum dialkyl dithiocarbamate (MoDTC) can cause wear acceleration of diamond-like carbon (DLC) coating coupled with steel under boundary lubrication, which hinders its industrial application. Therefore, polyisobutylene succinimide (PIBS), an organo molybdenum amide, was adopted to modify molybdenum oxide affording molybdenum polyisobutylene succinimide- molybdenum oxide nanoparticles (MPIBS-MONPs) with potential to prevent the wear acceleration of DLC coating. The thermal stability of MPIBS-MONPs was evaluated by thermogravimetric analysis. Their tribological properties as the additives in di-isooctyl sebacate (DIOS) were evaluated with MoDTC as a control; and their tribomechanism was investigated in relation to their tribochemical reactions and synergistic tribological effect with zinc dialkyldithiophosphate (ZDDP) as well as worn surface characterizations. Findings indicate that MPIBS-MONPs/ZDDP added in DIOS can significantly reduce the friction and wear of DLC coating, being much superior to MoDTC. This is because MPIBS-MONPs and ZDDP jointly take part in tribochemical reactions to form a composite tribofilm that can increase the wear resistance of DLC coating. Namely, the molybdenum amide on MPIBS-MONPs surface can react with ZDDP to form MoS2 film with excellent friction-reducing ability; and MPIBS-MONPs can release molybdenum oxide nanoparticle to form deposited lubrication layer on worn surfaces. The as-formed composite tribofilm consisting of molybdenum oxide nanocrystal, amorphous polyphosphate, and molybdenum disulfide as well as a small amount of Mo2C accounts for the increase in the wear resistance of DLC coating under boundary lubrication.

Graphical Abstract

Electronic Supplementary Material

Download File(s)
40544_0708_ESM.pdf (2.4 MB)

References

【1】
【1】
 
 
Friction
Pages 2021-2035

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
CHEN S, SONG N, ZHANG S, et al. Synergistic tribological effect between polyisobutylene succinimide-modified molybdenum oxide nanoparticle and zinc dialkyldithiophosphate for reducing friction and wear of diamond-like carbon coating under boundary lubrication. Friction, 2023, 11(11): 2021-2035. https://doi.org/10.1007/s40544-022-0708-4

1562

Views

90

Downloads

27

Crossref

30

Web of Science

31

Scopus

2

CSCD

Received: 29 June 2022
Revised: 12 September 2022
Accepted: 05 October 2022
Published: 25 March 2023
© The author(s) 2022.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.