AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (20.6 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Impact of chosen force fields and applied load on thin film lubrication

Thi D. TA1( ), Hien D. TA2, Kiet A. TIEU1, Bach H. TRAN1
School of Mechanical, Materials, Mechatronics, and Biomedical Engineering, University of Wollongong, NSW 2522, Australia
Ho Chi Minh City University of Technology and Education, Ho Chi Minh City 800010, Vietnam
Show Author Information

Abstract

The rapid development of molecular dynamics (MD) simulations, as well as classical and reactive atomic potentials, has enabled tribologists to gain new insights into lubrication performance at the fundamental level. However, the impact of adopted potentials on the rheological properties and tribological performance of hydrocarbons has not been researched adequately. This extensive study analyzed the effects of surface structure, applied load, and force field (FF) on the thin film lubrication of hexadecane. The lubricant film became more solid-like as the applied load increased. In particular, with increasing applied load, there was an increase in the velocity slip, shear viscosity, and friction. The degree of ordering structure also changed with the applied load but rather insignificantly. It was also significantly dependent on the surface structure. The chosen FFs significantly influenced the lubrication performance, rheological properties, and molecular structure. The adaptive intermolecular reactive empirical bond order (AIREBO) potential resulted in more significant liquid-like behaviors, and the smallest velocity slip, degree of ordering structure, and shear stress were compared using the optimized potential for liquid simulations of united atoms (OPLS-UAs), condensed-phase optimized molecular potential for atomic simulation studies (COMPASS), and ReaxFF. Generally, classical potentials, such as OPLS-UA and COMPASS, exhibit more solid-like behavior than reactive potentials do. Furthermore, owing to the solid-like behavior, the lubricant temperatures obtained from OPLS-UA and COMPASS were much lower than those obtained from AIREBO and ReaxFF. The increase in shear stress, as well as the decrease in velocity slip with an increase in the surface potential parameter ζ, remained conserved for all chosen FFs, thus indicating that the proposed surface potential parameter ζ for the COMPASS FF can be verified for a wide range of atomic models.

Electronic Supplementary Material

Download File(s)
40544_2020_464_MOESM1_ESM.pdf (783.4 KB)

References

【1】
【1】
 
 
Friction
Pages 1259-1274

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
TA TD, TA HD, TIEU KA, et al. Impact of chosen force fields and applied load on thin film lubrication. Friction, 2021, 9(5): 1259-1274. https://doi.org/10.1007/s40544-020-0464-2

1816

Views

108

Downloads

10

Crossref

9

Web of Science

9

Scopus

0

CSCD

Received: 06 July 2020
Revised: 01 September 2020
Accepted: 14 October 2020
Published: 07 January 2021
© The author(s) 2020

This article is licensed under a Creative Commons Attribution 4.0 International Li-cense, which permits use, sharing, adaptation, distribution and reproduction in any medium or for-mat, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not in-cluded in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.