AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (9.1 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Fast laser surface texturing of spherical samples to improve the frictional performance of elasto-hydrodynamic lubricated contacts

G. BOIDI1,2,3( ), P.G. GRÜTZMACHER4,5, A. KADIRIC1, F.J. PROFITO3, I.F. MACHADO3, C. GACHOT4, D. DINI1
Department of Mechanical Engineering, Imperial College London, South Kensington Campus, London SW7 2AZ, UK
AC2T research GmbH, Wiener Neustadt 2700, Austria
Polytechnic School, University of São Paulo-USP, São Paulo 05508-030, Brazil
Department of Engineering Design and Product Development, TU Wien, Wien 1060, Austria
Department of Material Science and Engineering, Saarland University, Saarbrücken 66123, Germany
Show Author Information

Abstract

Textured surfaces offer the potential to promote friction and wear reduction by increasing the hydrodynamic pressure, fluid uptake, or acting as oil or debris reservoirs. However, texturing techniques often require additional manufacturing steps and costs, thus frequently being not economically feasible for real engineering applications. This experimental study aims at applying a fast laser texturing technique on curved surfaces for obtaining superior tribological performances. A femtosecond pulsed laser (Ti:Sapphire) and direct laser interference patterning (with a solid-state Nd:YAG laser) were used for manufacturing dimple and groove patterns on curved steel surfaces (ball samples). Tribological tests were carried out under elasto-hydrodynamic lubricated contact conditions varying slide-roll ratio using a ball-on-disk configuration. Furthermore, a specific interferometry technique for rough surfaces was used to measure the film thickness of smooth and textured surfaces. Smooth steel samples were used to obtain data for the reference surface. The results showed that dimples promoted friction reduction (up to 20%) compared to the reference smooth specimens, whereas grooves generally caused less beneficial or detrimental effects. In addition, dimples promoted the formation of full film lubrication conditions at lower speeds. This study demonstrates how fast texturing techniques could potentially be used for improving the tribological performance of bearings as well as other mechanical components utilised in several engineering applications.

References

【1】
【1】
 
 
Friction
Pages 1227-1241

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
BOIDI G, GRÜTZMACHER P, KADIRIC A, et al. Fast laser surface texturing of spherical samples to improve the frictional performance of elasto-hydrodynamic lubricated contacts. Friction, 2021, 9(5): 1227-1241. https://doi.org/10.1007/s40544-020-0462-4

1692

Views

190

Downloads

67

Crossref

66

Web of Science

69

Scopus

5

CSCD

Received: 17 June 2020
Revised: 10 September 2020
Accepted: 14 October 2020
Published: 07 January 2021
© The author(s) 2020

This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.