AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Home Friction Article
PDF (27.7 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Temperature-mediated tribological characteristics of 40CrNiMoA steel and Inconel 718 alloy during sliding against Si3N4 counterparts

Liuyang BAI1,2, Shanhong WAN1,2( ), Gewen YI1,2( ), Yu SHAN1, Sang The PHAM3, Anh Kiet TIEU3, Yan LI4, Rendong WANG5
State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China
Center of Materials Science and Opto-Electronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China
Faculty of Engineering and Information Sciences, University of Wollongong, Wollongong 2522, Australia
State Key Laboratory of Metal Materials for Marine Equipment and Application, Anshan 114009, China
Ansteel Iron & Steel Research Institute, Anshan 114009, China
Show Author Information

Abstract

A comparative evaluation of the friction and wear behaviors of 40CrNiMoA steel and Inconel 718 alloy sliding against Si3N4 counterparts was conducted over a large temperature range from room temperature (RT) to 800 ℃. The temperature-dependent tribological properties associated with the resulting chemical mitigation and structural adaptation of the solid sliding surface were clarified by surface/interface characterizations. The results revealed desirable performance in reducing friction and wear at elevated temperatures, which was associated with the resulting oxide composite film's adaptive lubricating capability, whereas severe abrasive wear occurred at room/ambient temperatures. The oxidative-abrasive differentials for the two alloys were further discussed by considering the combined effect of temperature and stressed-shearing conditions.

References

【1】
【1】
 
 
Friction
Pages 1175-1197

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
BAI L, WAN S, YI G, et al. Temperature-mediated tribological characteristics of 40CrNiMoA steel and Inconel 718 alloy during sliding against Si3N4 counterparts. Friction, 2021, 9(5): 1175-1197. https://doi.org/10.1007/s40544-020-0455-3

1642

Views

191

Downloads

52

Crossref

N/A

Web of Science

50

Scopus

4

CSCD

Received: 10 March 2020
Revised: 30 July 2020
Accepted: 23 September 2020
Published: 01 December 2020
© The author(s) 2020

This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http:// creativecommons.org/licenses/by/4.0/.