Tribocorrosion properties of AISI 1045 and AISI 2205 steels in seawater: Synergistic interactions of wear and corrosion

Beibei ZHANG; Jianzhang WANG; Hao LIU; Yunfeng YAN; Pengfei JIANG; Fengyuan YAN

doi:10.1007/s40544-020-0376-1

Friction 2021, 9(5): 929-940 https://doi.org/10.1007/s40544-020-0376-1

Research Article |

Open Access | Issue | Published: 08 September 2020

Tribocorrosion properties of AISI 1045 and AISI 2205 steels in seawater: Synergistic interactions of wear and corrosion

Show Author's Information Hide Author's Information Beibei ZHANG^¹, Jianzhang WANG^¹, Hao LIU^¹, Yunfeng YAN^{¹^,²}, Pengfei JIANG^¹, Fengyuan YAN^¹(

)

1State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China

2Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China

Keywords:

tribocorrosion, passivation, synergistic effect, seawater

Cite this article:

ZHANG B, WANG J, LIU H, et al. Tribocorrosion properties of AISI 1045 and AISI 2205 steels in seawater: Synergistic interactions of wear and corrosion. Friction, 2021, 9(5): 929-940. https://doi.org/10.1007/s40544-020-0376-1

Download citation

EndNote(RIS)

BibTeX

745

Views

Downloads

Citations

Crossref

N/A

WoS

Scopus

CSCD

Abstract Full text About this article

Abstract

Tribocorrosion denotes an irreversible material degradation for several metallic components used in corrosive environments, and it arises from the interplay between chemical, mechanical, and electrochemical processes. In this study, some investigation has been performed to compare the tribocorrosion behavior of AISI 1045 steel and AISI 2205 duplex stainless steel sliding against an alumina pin in seawater. The lowering in the open circuit potential (OCP) of AISI 2205 during the tribocorrosion demonstrates that its protective passive film was damaged by wear and resulted in a wear-accelerated corrosion in the wear track. However, sliding was found to accelerate the corrosion of the unworn areas for AISI 1045, leading to an anodic shift of the OCP. Moreover, the total material loss increased with an increase in the applied potential for both materials. It was revealed that AISI 1045 was more sensitive to corrosion under sliding than AISI 2205. Therefore, pure corrosion loss and corrosion-induced wear constituted the primary reasons for the degradation of AISI 1045 at applied anodic potentials.

Full text

Abstract

Full text

Outline

About this article

Tribocorrosion properties of AISI 1045 and AISI 2205 steels in seawater: Synergistic interactions of wear and corrosion

Show Author's information Hide Author's Information Beibei ZHANG^¹, Jianzhang WANG^¹, Hao LIU^¹, Yunfeng YAN^{¹^,²}, Pengfei JIANG^¹, Fengyuan YAN^¹(

)

1State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China

2Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China

Abstract

Keywords: tribocorrosion, passivation, synergistic effect, seawater

References(31)

[1]

Ben Saada F, Elleuch K, Ponthiaux P. On the tribocorrosion responses of two stainless steels. Tribol Trans 61(1): 53-60 (2018)

DOI Google Scholar

[2]

Garcı́a I, Drees D, Celis J P. Corrosion-wear of passivating materials in sliding contacts based on a concept of active wear track area. Wear 249(5-6): 452-460 (2001)

DOI Google Scholar

[3]

Atık E, Yunker U, Merıç C. The effects of conventional heat treatment and boronizing on abrasive wear and corrosion of SAE 1010, SAE 1040, D2 and 304 steels. Tribol Int 36(3): 155-161 (2003)

DOI Google Scholar

[4]

Amann T, Gatti F, Oberle N, Kailer A, Rühe J. Galvanically induced potentials to enable minimal tribochemical wear of stainless steel lubricated with sodium chloride and ionic liquid aqueous solution. Friction 6(2): 230-242 (2018)

DOI Google Scholar

[5]

Dunnwald J, Otto A. An investigation of phase transitions in rust layers using Raman Spectroscopy. Corros Sci 29(9): 1167-1176 (1989)

DOI Google Scholar

[6]

Bello J O, Wood R J K, Wharton J A. Synergistic effects of micro-abrasion-corrosion of UNS S30403, S31603 and S32760 stainless steels. Wear 263(1-6): 149-159 (2007)

DOI Google Scholar

[7]

Chen J, Wang J Z, Yan F Y, Zhang Q, Li Q A. Effect of applied potential on the tribocorrosion behaviors of Monel K500 alloy in artificial seawater. Tribol Int 81: 1-8 (2015)

DOI Google Scholar

[8]

del Abra-Arzola J L, García-Rentería M A, Cruz-Hernández V L, García-Guerra J, Martínez-Landeros V H, Falcón-Franco L A, Curiel-López F F. Study of the effect of sigma phase precipitation on the sliding wear and corrosion behaviour of duplex stainless steel AISI 2205. Wear 400-401: 43-51 (2018)

DOI Google Scholar

[9]

Diomidis N, Celis J P, Ponthiaux P, Wenger F. A methodology for the assessment of the tribocorrosion of passivating metallic materials. Lubr Sci 21(2): 53-67 (2009)

DOI Google Scholar

[10]

Huttunen-Saarivirta E, Kilpi L, Hakala T J, Carpen L, Ronkainen H. Tribocorrosion study of martensitic and austenitic stainless steels in 0.01 M NaCl solution. Tribol Int 95: 358-371(2016)

DOI Google Scholar

[11]

Jun C. Corrosion wear characteristics of TC4, 316 stainless steel, and Monel K500 in artificial seawater. RSC Adv 7(38): 23835-23845 (2017)

Google Scholar

[12]

Moine M, Mary N, Normand B, Peguet L, Gaugain A, Evin H N. Tribo electrochemical behavior of ferrite and ferrite-martensite stainless steels in chloride and sulfate media. Wear 292-293: 41-48 (2012)

Google Scholar

[13]

Obadele B A, Andrews A, Shongwe M B, Olubambi P A. Tribocorrosion behaviours of AISI 310 and AISI 316 austenitic stainless steels in 3.5% NaCl solution. Mater Chem Phys 171: 239-246 (2016)

Google Scholar

[14]

Sun Y, Rana V. Tribocorrosion behaviour of AISI 304 stainless steel in 0.5 M NaCl solution. Mater Chem Phys 129(1-2): 138-147 (2011)

Google Scholar

[15]

Sun Y W, Yan X P, Yuan C Q, Bai X Q. Insight into tribological problems of green ship and corresponding research progresses. Friction 6(4): 472-483 (2018)

Google Scholar

[16]

Stratmann M, Bohnenkamp K, Engell H J. An electrochemical study of phase-transitions in rust layers. Corros Sci 23(9): 969-985 (1983)

Google Scholar

[17]

Stratmann M, Muller J. The mechanism of the oxygen reduction on rust-covered metal substrates. Corros Sci 36(2): 327-359 (1994)

Google Scholar

[18]

Asami K, Kikuchi M. In-depth distribution of rusts on a plain carbon steel and weathering steels exposed to coastal-industrial atmosphere for 17 years. Corros Sci 45(11): 2671-2688 (2003)

Google Scholar

[19]

Kamimura T, Hara S, Miyuki H, Yamashita M, Uchida H. Composition and protective ability of rust layer formed on weathering steel exposed to various environments. Corros Sci 48(9): 2799-2812 (2006)

Google Scholar

[20]

Liu J W, Jiang L, Deng C B, Du W H, Qian L M. Effect of oxide film on nanoscale mechanical removal of pure iron. Friction 6(3): 307-315 (2018)

Google Scholar

[21]

Guo H X, Lu B T, Luo J L. Interaction of mechanical and electrochemical factors in erosion-corrosion of carbon steel. Electrochim Acta 51(2): 315-323 (2005)

Google Scholar

[22]

López A, Bayón R, Pagano F, Igartua A, Arredondo A, Arana J L, González J J. Tribocorrosion behaviour of mooring high strength low alloy steels in synthetic seawater. Wear 338-339: 1-10 (2015)

Google Scholar

[23]

Tamura H. The role of rusts in corrosion and corrosion protection of iron and steel. Corros Sci 50(7): 1872-1883 (2008)

Google Scholar

[24]

Trausmuth A, Rodríguez Ripoll M, Zehethofer G, Vogl T, Badisch E. Impact of corrosion on sliding wear properties of low-alloyed carbon steel. Wear 328-329: 338-347 (2015)

Google Scholar

[25]

US-ASTM. ASTM standard D1141-98 Standard practice for the preparation of substitute ocean water. ASTM, 2013.

[26]

Tekin K C, Malayoglu U. Assessing the tribocorrosion performance of three different nickel-based superalloys. Tribol Lett 37(3): 563-572 (2009)

Google Scholar

[27]

Cai M R, Yu Q L, Zhou F, Liu W M. Physicochemistry aspects on frictional interfaces. Friction 5(4): 361-382 (2017)

Google Scholar

[28]

López-Ortega A, Bayón R, Arana J L, Arredondo A, Igartua A. Influence of temperature on the corrosion and tribocorrosion behaviour of High-Strength Low-Alloy steels used in offshore applications. Tribol Int 121: 341-352 (2018)

Google Scholar

[29]

US-ASTM. ASTM standard G119-09 Standard guide for determining synergism between wear and corrosion. ASTM, 2009.

[30]

Zhang B B, Wang J Z, Yan F Y. Load-dependent tribocorrosion behaviour of nickel-aluminium bronze in artificial seawater. Corros Sci 131: 252-263 (2018)

Google Scholar

[31]

Zhang B B, Wang J Z, Yuan J Y, Yan F Y. Tribocorrosion behavior of nickel aluminum bronze in seawater: Identification of corrosion-wear components and effect of pH. Mater Corros 69(1): 106-114 (2018)

Google Scholar

About this article

Publication history

Acknowledgements

Rights and permissions

Publication history

Received: 08 May 2019

Revised: 19 October 2019

Accepted: 24 February 2020

Published: 08 September 2020

Issue date: October 2021

Copyright

Acknowledgements

The work was financially supported by the National Natural Science Foundation of China (Grant No. 51405478) and Chinese Academy of Sciences "Light of West China" Program.

Rights and permissions

This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.