Journal Home > Volume 6 , Issue 3
Friction 2018, 6(3): 323-340 https://doi.org/10.1007/s40544-018-0226-6
Research Article | Open Access | Issue | Published: 10 August 2018

Acoustic emission characterization of sliding wear under condition of direct and inverse transformations in low- temperature degradation aged Y-TZP and Y-TZP-Al2O3

Show Author's Information Nikolai L SAVCHENKO1( ),  Andrey V FILIPPOV1,2,  Sergei Yu TARASOV1,2,  Andrey I DMITRIEV1,3,  Evgeny V SHILKO1,3,  Aleksandr S GRIGORIEV1
 Institute of Strength Physics and Materials Science SB RAS, Tomsk 634055, Russian Federation
 National Research Tomsk Polytechnic University, Tomsk 634050, Russian Federation
 National Research Tomsk State University, Tomsk 634050, Russian Federation
Keywords:
friction, zirconia, transformation toughening, low-temperature degradation, acoustic emission, numerical modeling, movable cellular automata method
Cite this article:
SAVCHENKO NL, FILIPPOV AV, TARASOV SY, et al. Acoustic emission characterization of sliding wear under condition of direct and inverse transformations in low- temperature degradation aged Y-TZP and Y-TZP-Al2O3. Friction, 2018, 6(3): 323-340. https://doi.org/10.1007/s40544-018-0226-6
Download citation
EndNote(RIS)
BibTeX

522

Views

8

Downloads

Citations

17

Crossref

N/A

WoS

16

Scopus

0

CSCD

Abstract Full text About this article

In this research, results of the investigation of the sliding friction and wear of yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) and Y-TZP-Al2O3 samples preliminarily subjected to low-temperature degradation are reported. The investigation was carried out using a pin-on-disk tribometer with simultaneous recording of acoustic emission (AE) and vibration acceleration. The sliding wear process was found to be determined by dynamic direct and inverse Y-TZP transformations detected by monoclinic and tetragonal X-ray diffraction peak ratios. The AE signals generated under direct and inverse transformations can be used to characterize wear and friction mechanisms as well as direct and inversed sliding-induced phase transformations. The AE signal energy grows with the friction coefficient and the inverse transformation degree. Reduction of the AE signal energy indicates establishing the mild wear stage caused by effective stress-induced direct martensitic transformation. The AE signal median frequency increases in the case of lower friction. Numerical studies of wear subsurface fracture under conditions of stress-induced martensitic transformation were used to elucidate the role played by the phase transformation in Y-TZP and Y-TZP-Al2O3. Martensitic transformation in Y-TZP was described with use of the non-associated dilatant plasticity model. Simulation results particularly show that increase in the value of dilatancy coefficient from 0 to 0.2 is accompanied by 25%−30% reduce in characteristic length and penetration depth of sliding-induced subsurface cracks. As shown the AE may be an effective tool for in-situ monitoring the subsurface wear of materials experiencing both direct and inverse transformations.


menu
Abstract
Full text
Outline
About this article

Acoustic emission characterization of sliding wear under condition of direct and inverse transformations in low- temperature degradation aged Y-TZP and Y-TZP-Al2O3

Show Author's information Nikolai L SAVCHENKO1( ), Andrey V FILIPPOV1,2, Sergei Yu TARASOV1,2, Andrey I DMITRIEV1,3, Evgeny V SHILKO1,3, Aleksandr S GRIGORIEV1
 Institute of Strength Physics and Materials Science SB RAS, Tomsk 634055, Russian Federation
 National Research Tomsk Polytechnic University, Tomsk 634050, Russian Federation
 National Research Tomsk State University, Tomsk 634050, Russian Federation

Abstract

In this research, results of the investigation of the sliding friction and wear of yttria-stabilized tetragonal zirconia polycrystalline (Y-TZP) and Y-TZP-Al2O3 samples preliminarily subjected to low-temperature degradation are reported. The investigation was carried out using a pin-on-disk tribometer with simultaneous recording of acoustic emission (AE) and vibration acceleration. The sliding wear process was found to be determined by dynamic direct and inverse Y-TZP transformations detected by monoclinic and tetragonal X-ray diffraction peak ratios. The AE signals generated under direct and inverse transformations can be used to characterize wear and friction mechanisms as well as direct and inversed sliding-induced phase transformations. The AE signal energy grows with the friction coefficient and the inverse transformation degree. Reduction of the AE signal energy indicates establishing the mild wear stage caused by effective stress-induced direct martensitic transformation. The AE signal median frequency increases in the case of lower friction. Numerical studies of wear subsurface fracture under conditions of stress-induced martensitic transformation were used to elucidate the role played by the phase transformation in Y-TZP and Y-TZP-Al2O3. Martensitic transformation in Y-TZP was described with use of the non-associated dilatant plasticity model. Simulation results particularly show that increase in the value of dilatancy coefficient from 0 to 0.2 is accompanied by 25%−30% reduce in characteristic length and penetration depth of sliding-induced subsurface cracks. As shown the AE may be an effective tool for in-situ monitoring the subsurface wear of materials experiencing both direct and inverse transformations.

Keywords: friction, zirconia, transformation toughening, low-temperature degradation, acoustic emission, numerical modeling, movable cellular automata method

References(40)

[1]
Turon-Vinas M, Anglada M. Strength and fracture toughness of zirconia dental ceramics. Dental Mater 34(3):365–375(2018)
Google Scholar
[2]
Deville S, Gremillard L, Chevalier J, Fantozzi G. A critical comparison of methods for the determination of the aging sensitivity in biomedical grade yttria-stabilized zirconia. J Biomed Mater Res Part B Appl Biomater 72B(2):239–245(2005)
Google Scholar
[3]
Reveron H, Fornabaio M, Palmero P, Fürderer T, Adolfsson E, Lughi V, Bonifacio A, Sergo V, Montanaro L, Chevalier J. Towards long lasting zirconia-based composites for dental implants: Transformation induced plasticity and its consequence on ceramic reliability. Acta Biomater 48:423–432(2017)
Google Scholar
[4]
Fischer T E, Anderson M P, Jahanmir S. Influence of fracture toughness on the wear resistance of yttria-doped zirconium oxide. J Am Ceram Soc 72(2):252–257(1989)
Google Scholar
[5]
Lee S W, Hsu S M, Shen M C. Ceramic wear maps: Zirconia. J Am Ceram Soc 76(8):1937–1947(1993)
Google Scholar
[6]
Swain M V, Hannink R H J. Metastability of the martensitic transformation in a 12 mol% ceria-zirconia alloy: II, grinding studies. J Am Ceram Soc 72(8):1358–1364(1989)
Google Scholar
[7]
Korolev P V, Savchenko N L, Kul’kov S N. Texture formation on the friction surface in transformation-toughened ceramics. Tech Phys Lett 30(1):12–14(2004)
Google Scholar
[8]
Becker P C, Libsch T A, Rhee S K. Wear mechanisms of toughened zirconias. In Proceedings of the 9th Annual Conference on Composites and Advanced Ceramic Materials. The American Ceramic Society, 1985: 1040-1058
[9]
Savchenko N L, Kul’kov S N. Friction and wear of Y-TZP and Y-TZP–Al2O3 ceramics in high-speed sliding on steel. J Frict Wear 30(6):444–448(2009)
Google Scholar
[10]
Wu K G, Choe C Y, Lee S M, Yoo J A, Hyun C Y, Hong D P, Byeon J W. Real-time monitoring of degradation of zirconia ceramic by acoustic emission. Appl Mech Mater 433–435:816–820(2013)
Google Scholar
[11]
Hua Z K, Fan Y W, Jin Z M. A biotribo-acoustic testing method for ceramic orthopaedic biomaterials. Tribol Int 71:1–6(2014)
DOI Google Scholar
[12]
Taylor S, Manley M T, Sutton K. The role of stripe wear in causing acoustic emissions from alumina ceramic-on-ceramic bearings. J Arthroplasty 22(S7):47–51(2007)
DOI Google Scholar
[13]
Wang L, Wood R J K. Acoustic emissions from lubricated hybrid contacts. Tribol Int 42(11–12):1629–1637(2009)
DOI Google Scholar
[14]
Filippov A V, Rubtsov V E, Tarasov S Y. Acoustic emission study of surface deterioration in tribocontacting. Appl Acoust 117:106–112(2017)
DOI Google Scholar
[15]
Filippov A V, Nikonov A Y, Rubtsov V E, Dmitriev A I, Tarasov S Y. Vibration and acoustic emission monitoring the stability of peakless tool turning: Experiment and modeling. J Mater Process Technol 246:224–234(2017).
DOI Google Scholar
[16]
Filippov A V, Tarasov S Y, Fortuna S V, Podgornykh O A, Shamarin N N, Rubtsov V E. Microstructural, mechanical and acoustic emission-assisted wear characterization of equal channel angular pressed (ECAP) low stacking fault energy brass. Tribol Int 123:273–285(2018)
DOI Google Scholar
[17]
Rubtsov V E, Kolubaev E A, Kolubaev A V, Popov V L. Using acoustic emission for the analysis of wear processes during sliding friction. Tech Phys Lett 39(2):223–225(2013)
DOI Google Scholar
[18]
McBride S L, Boness R J, Sobczyk M, Viner M R. Acoustics emission from lubricated and rubbing surfaces. J Acoust Emiss 8(1–2):192–196(1989)
Google Scholar
[19]
Clarke D R, Arora A. Acoustic emission characterization of the tetragonal-monoclinic phase transformation in zirconia. In Advances in Ceramics, Vol. 12, Science and Technology of Zirconia II. Claussen N, Heuer A H, Ruhle M, Eds. Columbus, OH: American Ceramic Society, 1984.
[20]
Lankford J. Plastic deformation of partially stabilized zirconia. J Am Ceram Soc 66(11):c212–c213(1983)
DOI Google Scholar
[21]
Drozdov A V, Galenko V O, Gogotsi G A, Swain M V. Acoustic emission during micro- and macrocrack growth in Mg-PSZ. J Am Ceram Soc 74(8):1922–1927(1991)
DOI Google Scholar
[22]
Chu L, Ren H, Ning J. Damage and Toughening Analysis of Ceramics by AE Location Method//Shen G. et al. (eds.), Advances in Acoustic Emission Technology: Proceedings of the World Conference on Acoustic Emission-2013, Springer Proceedings in Physics 158: 313–321
DOI
[23]
Jacobus K, Sehitoglu H, Balzer M. Effect of stress state on the stress-induced martensitic transformation in polycrystalline Ni-Ti Alloy. Metall Mater Trans A 27(10):3066–3073(1996)
DOI Google Scholar
[24]
Stam G T M, Van Der Giessen E, Meijers P. Effect of transformation-induced shear strains on crack growth in zirconia-containing ceramics. Int J Solids Struct 31(14):1923–1948(1994)
DOI Google Scholar
[25]
Sun Q P, Hwang K C. Micromechanics modelling for the constitutive behavior of polycrystalline shape memory alloys–I. Derivation of general relations. J Mech Phys Solids 41(1):1–17(1993)
DOI Google Scholar
[26]
Patoor E, Lagoudas D C, Entchev P B, Brinson L C, Gao X J. Shape memory alloys, Part I: General properties and modeling of single crystals. Mech Mater 38(5–6):391–429(2006)
DOI Google Scholar
[27]
Lagoudas D C, Entchev P B, Popov P, Patoor E, Brinson L C, Gao X J. Shape memory alloys, Part II: Modeling of polycrystals. Mech Mater 38(5–6):430–462(2006)
DOI Google Scholar
[28]
Lankford J, Page R A, Rabenberg L. Deformation mechanisms in yttria-stabilized zirconia. J Mater Sci 23(11):4144–4156(1988)
DOI Google Scholar
[29]
Nikolaevsky V N. Geomechanics and Fluidodynamics: with Applications to Reservoir Engineering. Dordrecht, Boston: Kluwer Academic, 1996
[30]
Stefanov Y P, Chertov M A, Aidagulov G R, Myasnikov A V. Dynamics of inelastic deformation of porous rocks and formation of localized compaction zones studied by numerical modeling. J Mech Phys Solids 59(11):2323–2340(2011)
DOI Google Scholar
[31]
Eremin M O. Numerical simulation of fracture of ZrO2-Al2O3 ceramic composites. Phys Mesomech 19(4):452–458(2016)
Google Scholar
[32]
Psakhie S, Shilko E V, Smolin A, Astafurov S, Ovcharenko V E. Development of a formalism of movable cellular automaton method for numerical modeling of fracture of heterogeneous elastic-plastic materials. Fract Struct Integr 7(24):26–59(2013)
Google Scholar
[33]
Shilko E V, Psakhie S G, Schmauder S, Popov V L, Astafurov S V, Smolin A Y. Overcoming the limitations of distinct element method for multiscale modeling of materials with multimodal internal structure. Comput Mater Sci 102:267–285(2015)
Google Scholar
[34]
Psakhie S G, Shilko E V, Grigoriev A S, Astafurov S V, Dimaki A V, Smolin A Y. A mathematical model of particle– particle interaction for discrete element based modeling of deformation and fracture of heterogeneous elastic–plastic materials. Eng Fract Mech 130:96–115(2014)
Google Scholar
[35]
Dmitriev A I, Österle W, Wetzel B, Zhang G. Mesoscale modeling of the mechanical and tribological behavior of a polymer matrix composite based on epoxy and 6 vol.% silica nanoparticles. Comput Mater Sci 110:204–214(2015)
Google Scholar
[36]
Alejano L R, Bobet A. Drucker-prager criterion. Rock Mech Rock Eng 45(6):995–999(2012)
Google Scholar
[37]
Dimaki A, Shilko E V, Psakhie S, Popov V L. Simulation of fracture using a mesh-dependent fracture criterion in the discrete element method. Facta Univ Ser Mech Eng 16(1):41–50(2018)
Google Scholar
[38]
Pohrt R, Popov V L. Adhesive contact simulation of elastic solids using local mesh-dependent detachment criterion in Boundary Elements Method. Facta Univ Ser Mech Eng 13(1):3–10(2015)
Google Scholar
[39]
Popov V L, Pohrt R, Li Q. Strength of adhesive contacts: Influence of contact geometry and material gradients. Friction 5(3):308–325(2017)
Google Scholar
[40]
Kelly J R, Denry I. Stabilized zirconia as a structural ceramic: An overview. Dent Mater 24(3):289–298(2008)
Google Scholar
Publication history
Copyright
Acknowledgements
Rights and permissions

Publication history

Received: 05 April 2018
Revised: 24 May 2018
Accepted: 14 June 2018
Published: 10 August 2018
Issue date: September 2018

Copyright

© The author(s) 2018

Acknowledgements

The work was financially supported by the Russian Federation via the Ministry of Education and Science of the Russian Federation (Agreement No. 14.607.21.0186, project identifier RFMEFI60717X0186).

Rights and permissions

This article is published with open access at Springerlink.com

Open Access: The articles published in this journal are distributed under the terms of the Creative Commons Attribution 4.0 International License (http:// creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Return