AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (3.2 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Ultrathin NiO/Ni3S2 Heterostructure as Electrocatalyst for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries

Chunqiao Jin1, Pengbo Zhai3, Jianli Tang1, Liuxiang Huo1, Qianqian He3, Yan Ye1, Lingxi Qiu1, Kai Jiang1, Liyan Shang1, Yawei Li1, Yongji Gong3( ), Zhigao Hu1,2 ( ), Junhao Chu1,2
Department of Materials, School of Physics and Electronic Science, Technical Center for Multifunctional Magneto-Optical Spectroscopy (Shanghai), Engineering Research Center of Nanophotonics & Advanced Instrument (Ministry of Education), East China Normal University, Shanghai 200241, China
Collaborative Innovation Center of Extreme Optics, Shanxi University, Taiyuan Shanxi 030006, China
School of Materials Science and Engineering, Beihang University, Beijing 100191, China
Show Author Information

Abstract

The practical application of Lithium–Sulfur batteries largely depends on highly efficient utilization and conversion of sulfur under the realistic condition of high-sulfur content and low electrolyte/sulfur ratio. Rational design of heterostructure electrocatalysts with abundant active sites and strong interfacial electronic interactions is a promising but still challenging strategy for preventing shuttling of polysulfides in lithium–sulfur batteries. Herein, ultrathin nonlayered NiO/Ni3S2 heterostructure nanosheets are developed through topochemical transformation of layered Ni(OH)2 templates to improve the utilization of sulfur and facilitate stable cycling of batteries. As a multifunction catalyst, NiO/Ni3S2 not only enhances the adsorption of polysulfides and shorten the transport path of Li ions and electrons but also promotes the Li2S formation and transformation, which are verified by both in-situ Raman spectroscopy and electrochemical investigations. Thus, the cell with NiO/Ni3S2 as electrocatalyst delivers an area capacity of 4.8 mAh cm−2 under the high sulfur loading (6 mg cm−2) and low electrolyte/sulfur ratio (4.3 μL mg−1). The strategy can be extended to 2D Ni foil, demonstrating its prospects in the construction of electrodes with high gravimetric/volumetric energy densities. The designed electrocatalyst of ultrathin nonlayered heterostructure will shed light on achieving high energy density lithium–sulfur batteries.

Electronic Supplementary Material

Download File(s)
eem-6-6-e12491_ESM.docx (60.6 MB)

References

【1】
【1】
 
 
Energy & Environmental Materials

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Jin C, Zhai P, Tang J, et al. Ultrathin NiO/Ni3S2 Heterostructure as Electrocatalyst for Accelerated Polysulfide Conversion in Lithium–Sulfur Batteries. Energy & Environmental Materials, 2023, 6(6). https://doi.org/10.1002/eem2.12491

611

Views

3

Downloads

47

Crossref

57

Web of Science

51

Scopus

3

CSCD

Received: 25 April 2022
Revised: 17 July 2022
Published: 26 July 2022
© 2022 The Authors.

This is an open access article under the terms of the Creative Commons Attribution License, which permits use, distribution and reproduction in any medium, provided the original work is properly cited.