AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (3.5 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article

Sodium Diffuses from Glass Substrates through P1 Lines and Passivates Defects in Perovskite Solar Modules

Felix Utama Kosasih1 ( ), Francesco Di Giacomo2, Jordi Ferrer Orri1,3, Kexue Li4, Elizabeth M. Tennyson3 , Weiwei Li1 , Fabio Matteocci2, Gunnar Kusch1 , Narges Yaghoobi Nia2, Rachel A. Oliver1, Judith L. MacManus-Driscoll1, Katie L. Moore4 , Samuel D. Stranks3,5, Aldo Di Carlo2,6 , Giorgio Divitini1 , Caterina Ducati1( )
Department of Materials Science and Metallurgy, University of Cambridge, 27 Charles Babbage Road, Cambridge CB3 0FS, UK
Centre for Hybrid and Organic Solar Energy (CHOSE), Department of Electronic Engineering, University of Rome Tor Vergata, Rome 00133, Italy
Cavendish Laboratory, University of Cambridge, JJ Thomson Avenue, Cambridge CB3 0HE, UK
Department of Materials and Photon Science Institute, University of Manchester, Oxford Road, Manchester M13 9PL, UK
Department of Chemical Engineering and Biotechnology, University of Cambridge, Philippa Fawcett Drive, Cambridge CB3 0AS, UK
Laboratory for Advanced Solar Energy (LASE), National University of Science and Technology MISiS, Leninskiy Prospekt 4, Moscow 119049, Russia
Show Author Information

Abstract

Most thin-film photovoltaic modules are constructed on soda-lime glass (SLG) substrates containing alkali oxides, such as Na2O. Na may diffuse from SLG into a module's active layers through P1 lines, an area between a module's constituent cells where the substrate-side charge transport layer (CTL) is in direct contact with SLG. Na diffusion from SLG is known to cause several important effects in Ⅱ–Ⅵ and chalcogenide solar modules, but it has not been studied in perovskite solar modules (PSMs). In this work, we use complementary microscopy and spectroscopy techniques to show that Na diffusion occurs in the fabrication process of PSMs. Na diffuses vertically inside P1 lines and then laterally from P1 lines into the active area for up to 360 μm. We propose that this process is driven by the high temperatures the devices are exposed to during CTL and perovskite annealing. The diffused Na preferentially binds with Br, forming Br-poor, I-rich perovskite and a species rich in Na and Br (Na-Br) close to P1 lines. Na-Br passivates defect sites, reducing non-radiative recombination in the perovskite and boosting its luminescence by up to 5×. Na-Br is observed to be stable after 12 weeks of device storage, suggesting long-lasting effects of Na diffusion. Our results not only point to a potential avenue to increase PSM performance but also highlight the possibility of unabated Na diffusion throughout a module's lifetime, especially if accelerated by the electric field and elevated temperatures achievable during device operation.

Electronic Supplementary Material

Download File(s)
eem-6-6-e12459_ESM.pdf (1.9 MB)

References

【1】
【1】
 
 
Energy & Environmental Materials

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Kosasih FU, Giacomo FD, Orri JF, et al. Sodium Diffuses from Glass Substrates through P1 Lines and Passivates Defects in Perovskite Solar Modules. Energy & Environmental Materials, 2023, 6(6). https://doi.org/10.1002/eem2.12459

582

Views

4

Downloads

10

Crossref

10

Web of Science

10

Scopus

0

CSCD

Received: 29 March 2022
Revised: 19 May 2022
Published: 16 June 2022
© 2022 Zhengzhou University.