AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (2 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article

Stable Methylammonium-Free p-i-n Perovskite Solar Cells and Mini-Modules with Phenothiazine Dimers as Hole-Transporting Materials

Luigi Angelo Castriotta1, Rossella Infantino2,3, Luigi Vesce1, Maurizio Stefanelli1, Alessio Dessì2, Carmen Coppola3,4, Massimo Calamante2,5, Gianna Reginato2, Alessandro Mordini2,5, Adalgisa Sinicropi2,3,4, Aldo Di Carlo1,6 ( ), Lorenzo Zani2 ( )
Centre for Hybrid and Organic Solar Energy (C.H.O.S.E.), Department of Electronic Engineering, University of Rome Tor Vergata, 00133 Rome, Italy
Institute of Chemistry of Organometallic Compounds (CNR-ICCOM, Via Madonna del Piano 10, 50019 Sesto Fiorentino, Italy
Department of Biotechnology, Chemistry and Pharmacy, University of Siena, Via Aldo Moro 2, 53100 Siena, Italy
CSGI, Consorzio per lo Sviluppo dei Sistemi a Grande Interfase, Via della Lastruccia 3, 50019 Sesto Fiorentino, Italy
Department of Chemistry "U. Schiff", University of Florence, Via della Lastruccia 13, 50019 Sesto Fiorentino, Italy
Institute of Structure of Matter (CNR-ISM), Via del Fosso del Cavaliere 100, 00133 Rome, Italy
Show Author Information

Abstract

During the last decade, perovskite solar technologies underwent an impressive development, with power conversion efficiencies reaching 25.5% for single-junction devices and 29.8% for Silicon-Perovskite tandem configurations. Even though research mainly focused on improving the efficiency of perovskite photovoltaics (PV), stability and scalability remain fundamental aspects of a mature photovoltaics technology. For n-i-p structure perovskite solar cells, using poly-triaryl(amine) (PTAA) as hole transport layer (HTL) allowed to achieve marked improvements in device stability compared with other common hole conductors. For p-i-n structure, poly-triaryl(amine) is also routinely used as dopant-free hole transport layer, but problems in perovskite film growth, and its limited resistance to stress and imperfect batch-to-batch reproducibility, hamper its use for device upscaling. Following previous computational investigations, in this work, we report the synthesis of two small-molecule organic hole transport layers (BPT-1,2), aiming to solve the above-mentioned issues and allow upscale to the module level. By using BPT-1 and methylammonium-free perovskite, max. Power conversion efficiencies of 17.26% and 15.42% on a small area (0.09 cm2) and mini-module size (2.25 cm2), respectively, were obtained, with a better reproducibility than with poly-triaryl(amine). Moreover, BPT-1 was demonstrated to yield more stable devices compared with poly-triaryl(amine) under ISOS-D1, T1, and L1 accelerated life-test protocols, reaching maximum T90 values >1000 h on all tests.

Electronic Supplementary Material

Download File(s)
eem-6-6-e12455_ESM.pdf (1.8 MB)

References

【1】
【1】
 
 
Energy & Environmental Materials

{{item.num}}

Comments on this article

Go to comment

< Back to all reports

Review Status: {{reviewData.commendedNum}} Commended , {{reviewData.revisionRequiredNum}} Revision Required , {{reviewData.notCommendedNum}} Not Commended Under Peer Review

Review Comment

Close
Close
Cite this article:
Castriotta LA, Infantino R, Vesce L, et al. Stable Methylammonium-Free p-i-n Perovskite Solar Cells and Mini-Modules with Phenothiazine Dimers as Hole-Transporting Materials. Energy & Environmental Materials, 2023, 6(6). https://doi.org/10.1002/eem2.12455

565

Views

5

Downloads

17

Crossref

12

Web of Science

13

Scopus

1

CSCD

Received: 25 February 2022
Revised: 01 June 2022
Published: 12 June 2022
© 2022 Zhengzhou University.